Mortara Surveyor S4 User Manual (English)

Other manuals for Mortara Surveyor S4

Questions and Answers:

M
Mark JohnsonAug 18, 2025
What to do if my Mortara Medical Equipment shows 'No ECG Monitoring' alarm and won't connect to Central?
- C
  Christopher WebbAug 18, 2025
  To address the 'No ECG Monitoring' alarm, 'Trying to connect to Central' error, an X symbol on the WiFi indicator, a fast blinking blue LED, 'AP MAC: Not-Associated' message, invalid IP address, or inability to ping on your Mortara Medical Equipment, check your WiFi network settings. If issues persist, contact your IT Network Administrator, as the cause may be an incorrect WLAN configuration or WLAN infrastructure problems.
S
Stacey LivingstonAug 21, 2025
Why does my Mortara Medical Equipment have intermittent 'No ECG Monitoring' alarms and connection issues?
- D
  Daniel RiveraAug 21, 2025
  To fix intermittent traces or 'No ECG Monitoring' alarms, 'Trying to connect to Central' errors, a low WiFi signal, intermittent blinking blue LED, 'AP MAC: Not-Associated' messages, or inconsistent ping results on your Mortara Medical Equipment, the cause may be poor WLAN network coverage. Contact your IT Network Administrator to correct these issues.
J
Justin CardenasAug 23, 2025
What to do if my Mortara Medical Equipment displays a 'No ECG Monitoring' alarm but has a normal WiFi signal?
- D
  Dr. Sarah MartinezAug 23, 2025
  To resolve the issue with your Mortara Medical Equipment displaying a 'No ECG Monitoring' alarm and failing to show traces on the Central Station, displaying a 'Trying to connect to Central' error, showing a normal WiFi signal, a slow blinking blue LED, correctly populated network info, an invalid IP address, and an inability to ping, check your LAN network settings. The cause may be an incorrect LAN configuration or LAN infrastructure issues. Contact your IT Network Administrator to correct these issues.
D
daisy88Aug 26, 2025
Why does my Mortara Medical Equipment show 'No ECG Monitoring' alarm even with a valid IP address?
- J
  john73Aug 26, 2025
  To resolve the 'No ECG Monitoring' alarm and connection issues on your Mortara Medical Equipment, where the device displays a 'Trying to connect to Central' error, shows a normal WiFi signal and slow blinking blue LED, has correctly populated network info, a valid IP address, and successful pings for some IPs, check the S4 Host settings and Central Station configuration. The issue may stem from an incorrect Host/Central stations configuration, a mismatch between Unit/Bed ID and Base Port configuration, the Surveyor Central Station not running, an incorrectly configured security router, or LAN infrastructure issues. Also, check the security router configuration and status, and ensure that LAN IPv4 network settings are correct. Contact your IT Network Administrator if needed.
S
Shane WoodardAug 28, 2025
How to fix 'Trying to connect to Central...' message on Mortara Medical Equipment?
- D
  dcohenAug 28, 2025
  If your Mortara Medical Equipment displays 'Trying to connect to Central...', this indicates it is not able to connect to the Surveyor Central Station. Check the network settings and access of the WiFi network. Also, refer to the Network Transmission items.
R
Robin ThompsonAug 30, 2025
Why is the ECG signal noisy on my Mortara Medical Equipment?
- F
  Frederick MillerAug 31, 2025
  If the ECG signal from your Mortara Medical Equipment is noisy, there are several potential causes and solutions: * **Excessive patient movement:** Confirm electrode site preparation and correct ECG positioning; move electrodes if needed. * **Electrical noise:** Isolate the patient from auxiliary equipment, if possible. * **Bad electrode contact:** Check to make sure electrodes are still securely attached to the patient, and reattach if necessary. Remember the importance of good skin preparation techniques.
J
Jacqueline ColemanSep 2, 2025
How to fix a Mortara S4 Medical Equipment when it's not working and the display is off?
- D
  Dennis TorresSep 2, 2025
  If your Mortara S4 Medical Equipment is not working and the display does not light up, it could be due to an internal system failure or a battery issue. Try power cycling the S4 with fresh batteries. If problems persist, stop using the S4 and contact Mortara Technical Support. If the battery will not hold a charge, replace it according to the instructions in the General Care & Maintenance chapter.
J
Joy BryantSep 4, 2025
What to do if the touchscreen on my Mortara S4 Medical Equipment is not working?
- C
  Carrie HernandezSep 4, 2025
  If the touchscreen on your Mortara S4 Medical Equipment is not working properly, it could be due to a touchscreen failure. Try power cycling the S4. If problems persist, stop using the S4 and contact Mortara Technical Support.
L
laurabergerSep 7, 2025
What to do if the display is not working on my Mortara S4 Medical Equipment?
- C
  Courtney FlowersSep 7, 2025
  If the display on your Mortara S4 Medical Equipment is not working properly, it may be due to a display failure. Try power cycling the S4. If problems persist, stop using the S4 and contact Mortara Technical Support.
J
Jessica StanleySep 9, 2025
How to resolve 'Enter New Passcode' error on Mortara Medical Equipment?
- R
  Rachel ThompsonSep 9, 2025
  If your Mortara Medical Equipment displays 'Enter New Passcode', ensure that the configuration passcode entered as well as the confirmation passcode values match.