EasyManua.ls Logo

mspa Rimba - User Manual

mspa Rimba
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
®
www.the-mspa.com
Owner’s Manual
Due to MSpa's continuous product improvement process, MSpa reserves the right to change the specifications and appearance of its
products, which may result in updates to the instruction manual without prior notice.
U-NE022 Nest
U-RB062/082 Rimba
U-AU062 Aurora
U-VT062 Vito
PLEASE DO NOT RETURN THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?MISSING PARTS?
For FAQ, Manuals, Videos or Spare Parts, please visit
www.the-mspa.com/support
EN

Table of Contents

Questions and Answers

  • T
    Teresa WoodAug 18, 2025
    Why is my mspa Rimba not heating properly?
    • J
      Jacqueline GeorgeAug 18, 2025
      Your MSpa Hot Tub might not be heating properly due to several reasons. Check if the temperature is set too low and increase it. A dirty filter cartridge can also cause this, so clean or replace it. Ensure the water level is at least at the minimum line. If these steps don't resolve the issue, there may be a heater failure, or the filter pump may not be working; in the latter case, refer to the section on 'FILTER PUMP DOES NOT WORK'.
  • S
    Steven AndersonAug 20, 2025
    How to clean the water in my mspa Rimba Hot Tub?
    • C
      Craig WilsonAug 20, 2025
      To clean the water in your MSpa Hot Tub, start by changing the water if it has been used for a long time. Ensure you extend the filtration time. Regularly clean or replace the filter cartridge. Also, maintain proper water balance by referring to the chemical manufacturer’s instructions.
  • W
    William WalkerAug 22, 2025
    What to do if my MSpa Hot Tub is leaking?
    • P
      penny06Aug 23, 2025
      If your MSpa Hot Tub is leaking, first check whether the spa in&outlet connection is securely tight and tighten it if necessary. Ensure the drainage valve is completely closed. If the spa pool body is leaking, repair the hole or split using the repair kit material.
  • J
    Jill WardAug 25, 2025
    Why is my mspa Rimba Hot Tub losing air?
    • D
      dawn96Aug 26, 2025
      Your MSpa Hot Tub might be losing air because the air valve is loose. Inflate the spa until the yellow section of the manometer is pushed out and ensure the valve is screwed tightly; replace the valve if needed. Another reason could be a hole or split on the spa tub. To locate it, fill a squirt bottle with soapy water and spray on the seams; small bubbles will appear where there is a leak. Clean and dry the leaking area, then use the repair patch supplied with your spa.
  • C
    Christopher BanksAug 28, 2025
    What to do if there is no display on the control panel of my MSpa Hot Tub?
    • C
      collinsjamesAug 28, 2025
      If there is no display on the control panel of your MSpa Hot Tub, first check the power socket and change or repair it if it's faulty. If the socket is fine, reset the PRCD by following the PRCD Testing section. If the controller is still not displayed after pressing the reset button, it might indicate a broken PRCD.
  • P
    Patrick AndersonAug 30, 2025
    How to fix a MSpa Hot Tub that loses air?
    • C
      Catherine Brewer PhDAug 30, 2025
      If your MSpa Hot Tub is losing air, ensure the air valve is tightly screwed in and inflate the spa until the yellow section of the manometer is pushed out. If necessary, replace the valve. Also, inspect the spa tub for holes or splits by applying soapy water to the seams; repair any leaks with the provided patch.
  • B
    Benjamin FarleySep 1, 2025
    Why doesn't the filter pump work in my MSpa Hot Tub?
    • N
      Nancy VasquezSep 1, 2025
      If the filter pump in your MSpa hot tub isn't working, the filter cartridge might be clogged with dirt or other objects. Clean or replace the filter cartridge. If the issue persists, contact the MSpa Service Center, as there may be a filter system failure.
  • A
    Adam CrawfordSep 4, 2025
    How to fix my mspa Rimba that loses air?
    • J
      Jessica WrightSep 4, 2025
      If your MSpa hot tub is losing air, make sure the air valve is screwed tightly. Inflate the spa until the yellow section of the manometer is pushed out. Replace the valve if necessary. If there's a hole or split on the spa tub, use soapy water to locate the leak, then clean and dry the area before applying the repair patch.
  • B
    Brandy StricklandSep 6, 2025
    Why is there no bubble in my mspa Rimba Hot Tub?
    • F
      Felicia BoydSep 6, 2025
      If there are no bubbles in your MSpa hot tub, wait for 10 minutes and turn on the Bubble button again, as it may have auto-off after 10 minutes. If the issue persists, contact the MSpa Service Center, as internal parts may be damaged or the one-way valve may be broken.
  • E
    Edward ArmstrongSep 9, 2025
    How to fix no display on the mspa Rimba Hot Tub control panel?
    • K
      Kyle HallSep 9, 2025
      If there is no display on the control panel of your MSpa Hot Tub, first check the power socket. Change the socket or repair the socket before use if it has failed. Also, check if the PRCD is off and reset it by following the PRCD Testing section. If, after pressing the Reset button, the controller is still not displayed, it may be broken.

Summary

Safety Precautions

First Use and Setup Preparation

Site Preparation and Requirements

Details site requirements for installing the MSpa, including surface and drainage.

PRCD Testing

Instructions for testing the PRCD (Portable Residual Current Device) for safety.

Spa Setup

Step-by-step guide for setting up the MSpa, including unboxing and inflating.

Controller Operation

HEATING

Details how to operate the heating system, including temperature settings.

FILTRATION

Instructions for operating the filtration system and filter cleaning reminders.

BUBBLE MASSAGE

Explains how to use the bubble massage function and its settings.

HEATING TIMER

UVC SANITIZER

OZONE

SAFETY LOCK

Water Maintenance and Chemicals

Filter Cartridge Maintenance

Spa Water

Water Sanitation

Water Balance

Drainage, Cleaning and Storage

Spa Drainage

Cleaning The Spa Tub

Deflation Instructions

Troubleshooting

Error Code Chart

Table listing error codes, their causes, and solutions.

mspa Rimba Specifications

General IconGeneral
DimensionsHeight: 70 cm / 28"
Water Capacity184 Gal
Heating System1.2 - 1.8°C/Hour
JetsAir Jets
Control SystemDigital
Heat Increasing Rate1.2 - 1.8°C/Hour
Power Supply220-240V / 50Hz
Temperature Range20-40°C

Related product manuals