EasyManua.ls Logo

MTD 550 Thru 570 - User Manual

MTD 550 Thru 570
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
PRINTED IN U.S.A
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
IMPORTANT
OPERATOR’S MANUAL
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
01/24/2007
FORM NO. 770-10529F
Log Splitter — Model Series 550 Thru 570
* Model 24BF572B729 Shown

Table of Contents

Questions and Answers

  • D
    David LawrenceSep 23, 2025
    What to do if my MTD Log Splitter runs but wood won't split or splits too slowly?
    • W
      wgonzalesSep 23, 2025
      If your MTD Log Splitter engine runs, but the wood will not split or splits too slowly, make sure that pump inlet hoses are clear and unblocked. Check the oil level. If the oil is contaminated, drain the oil, clean reservoir, and refill. Also, do not attempt to split wood against the grain.
  • J
    Joseph LopezAug 25, 2025
    Why drivebelt slips on MTD 550 Thru 570 Edger?
    • T
      Timothy CervantesAug 25, 2025
      A drivebelt on your MTD Edger might slip because the belt is worn or stretched. Replace the drive belt to resolve this issue.
  • K
    Kelly BerryAug 25, 2025
    How to fix occasional skips at high speed on my MTD Lawn Mower?
    • M
      Miss Crystal LopezAug 26, 2025
      If your MTD Lawn Mower occasionally skips or hesitates at high speed, the spark plug gap may be too close. Adjust the gap, referring to the Engine Operator’s Manual for the correct gap specifications.
  • M
    Mark SchwartzAug 27, 2025
    What to do if the drive-belt slips on my MTD Lawn Mower?
    • D
      Dylan RayAug 27, 2025
      If the drive-belt slips on your MTD Lawn Mower, it is likely worn or stretched and needs to be replaced.
  • A
    amatthewsSep 23, 2025
    Why is my MTD Log Splitter pump shaft seal leaking?
    • A
      Amber SalazarSep 23, 2025
      If there is a leaking pump shaft seal on your MTD Log Splitter, it may be due to engine/pump misalignment. Correct alignment as necessary. Also, make certain the reservoir is properly vented.
  • J
    Jennifer CruzSep 13, 2025
    Why MTD Log Splitter engine will not turn or stalls under low load conditions?
    • H
      Heather LittleSep 13, 2025
      If the engine on your MTD Log Splitter will not turn or stalls under low load conditions, the issue could be: * Engine/pump misalignment. Correct alignment as necessary. * Hydraulic lines blocked. Flush and clean hydraulic system. * Blocked directional valve. Flush and clean hydraulic system.
  • G
    Gregory JoyceSep 12, 2025
    Why MTD Log Splitter engine stalls during splitting?
    • A
      Alexander HudsonSep 12, 2025
      If your MTD Log Splitter engine stalls during splitting, it might be due to an overloaded cylinder. Avoid attempting to split wood against the grain.
  • A
    angelahowardSep 12, 2025
    Why is the cylinder shaft speed slow on my MTD Log Splitter?
    • M
      Mrs. Michelle JenkinsSep 12, 2025
      If the cylinder shaft speed is slow while extending and retracting on your MTD Log Splitter, it could be due to: * Excessive pump inlet vacuum. Make certain pump inlet hoses are clear and unblocked; use short, large diameter inlet hoses. * Incorrect oil level. Check the oil level. * Contaminated oil. Drain oil, clean reservoir and refill.
  • D
    Donna NixonSep 4, 2025
    What causes excessive vibration in MTD 550 Thru 570?
    • A
      Andrew SavageSep 4, 2025
      Excessive vibration in your MTD Edger can be caused by: * A bent or damaged edger blade; replace the edger blade. * A bent or damaged blade spindle.
  • J
    janicewilliamsSep 2, 2025
    What to do if MTD 550 Thru 570 engine runs erratic?
    • T
      Theresa RaySep 2, 2025
      If your MTD Edger engine is running erratically, consider the following: * Check the spark plug wire and connect and tighten if loose. * Drain any stale fuel from the gasoline tank and refill with fresh fuel. * Ensure the vent in the gas cap isn't plugged; clear any debris. * Drain the fuel tank and refill with fresh fuel if there's water or dirt in the fuel system.

MTD 550 Thru 570 Specifications

General IconGeneral
BrandMTD
Model550 Thru 570
CategoryEdger
LanguageEnglish

Related product manuals