Why is there no sound from my NAD Amplifier?
Several factors could cause a lack of sound from your NAD Amplifier. First, verify that the mains power cord is securely plugged in and the power is switched ON. Ensure that the TAPE MONITOR mode is de-selected and that Mute is switched off. Lastly, check that the rear PRE OUT/MAIN IN amp links are properly fitted.
What to do if my NAD C356BEE Amplifier C 356BEE does not respond to remote control commands?
If your NAD Amplifier C 356BEE isn't responding to remote commands, start by checking the remote's battery to ensure it is not flat or incorrectly inserted; follow the correct battery insertion setup. Also, verify that the infrared receiver (IR) window on both the C 356BEE and the remote control's IR transmitter are not obstructed, ensuring a clear line-of-sight. Finally, check if the IR receiver is exposed to direct sunlight or very bright ambient light, and if so, move the unit away from direct sun or reduce the ambient light.
What to do if Standby LED turns red during NAD C356BEE operation?
If the Standby LED on your NAD Amplifier turns red during operation, it could indicate that the C 356BEE has overheated or that the overall impedance of the loudspeakers is too low. To resolve overheating, shut down the C 356BEE using the rear panel POWER switch, ensure adequate space around the unit for airflow, let it cool down, and then turn it back ON. Also, make sure the overall loudspeaker impedance is not below 4 ohms.
Why is there no sound from one channel of my NAD C356BEE Amplifier?
If you're experiencing sound from only one channel of your NAD Amplifier, first ensure that the Balance control is centered. Then, check the speaker connections and the speakers themselves for any damage. Also, inspect the input leads and their connections for any disconnections or damage.
What to do if there is no audio from NAD C356BEE despite active input at MP rear panel input terminals?
If there is no audio despite having an active input at the MP rear panel input terminals of your NAD Amplifier, it may be due to an external Media Player being connected to the front MP socket. Disconnect the Media Player from the front MP socket.
How to fix weak bass or diffused stereo image on NAD Amplifier?
To fix weak bass or a diffused stereo image on your NAD Amplifier, check the connections to all speakers in the system to ensure they are wired correctly and in phase.
What to do if there is no audio from NAD Amplifier despite active input at DISC rear panel input terminals?
If there is no audio despite the presence of an active input at the DISC rear panel input terminals on your NAD Amplifier, it might be because the DISC input is disabled due to an installed MDC module at the MDC Classic Upgrade slot. Try uninstalling the MDC module from the MDC Classic Upgrade slot.
Covers reading instructions, cleaning, water, attachments, ventilation, power, grounding, and cord protection.
Details antenna grounding, lightning, power lines, overloading, and object/liquid entry precautions.
Covers service, mounting, heat, headphones, battery disposal, and general warnings.
Discusses waste disposal, battery collection, voltage notes, and recording model/serial numbers.
Offers step-by-step instructions for initial setup and connection of the C 356BEE.
Provides a table of common problems like no sound, weak bass, or unresponsive remote, with solutions.
General| Amplifier class | A |
|---|---|
| Frequency range | 10 - 65000 Hz |
| Audio output channels | 2.0 channels |
| Peak power per channel | - W |
| Signal-to-Noise Ratio (SNR) | 110 dB |
| Total Harmonic Distortion (THD) | 0.009 % |
| Dynamic power per channel (2 Ohm) | 290 W |
| Dynamic power per channel (4 Ohm) | 220 W |
| Dynamic power per channel (8 Ohm) | 145 W |
| RMS power output per channel (4 Ohm) | 80 W |
| AC (power) in | Yes |
| Audio (L/R) in | 8 |
| Audio (L/R) out | 6 |
| Headphone connectivity | 3.5 mm |
| USB 2.0 ports quantity | 1 |
| Speakers connectivity type | Binding post |
| Purpose | Home |
| Product color | Black |
| Volume control | Rotary |
| Connectivity technology | Wired |
| Sustainability certificates | RoHS |
| Maximum current | 1.5 A |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 350 W |
| Package weight | 10600 g |
Weight and Dimensions| Depth | 337 mm |
|---|---|
| Width | 435 mm |
| Height | 130 mm |
| Weight | 8700 g |
To Next Page
