EasyManua.ls Logo

NANO NDL-130 - User Manual

Default Icon
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
User guide
heatless desiccant air dryer
revision: 2022-116 document: 17-100-0120
© 2022 Air & Gas Solutions LLC.
www.n-psi.co.uk

Table of Contents

Other manuals for NANO NDL-130

Preview: Maintenance Service Manual
Maintenance Service Manual26 pages

Questions and Answers

  • I
    isaacbenderAug 9, 2025
    What to do if my NANO NDL-130 Dehumidifier is not cycling?
    • B
      Breanna ThomasAug 10, 2025
      If your NANO Dehumidifier isn't cycling, first ensure the controller is powered and check the on-screen column status to confirm it's powering the solenoid valves during normal operation. Also, check the power to the unit and the fuse (T2A 250V) located at Fig 8.A. Insufficient inlet pressure could also be the culprit; ensure it's at least 4 barg and adjust the inlet pressure settings if needed. A failure to de-pressurize during cycling could indicate a solenoid valve malfunction. If the coil has power, replace the valve. A working valve should produce an audible click when energized. Finally, check the inlet air supply if the outlet flow stops.
  • R
    Rodney WardAug 18, 2025
    Why does my NANO NDL-130 have poor dew point performance?
    • J
      Jaclyn SloanAug 18, 2025
      If your NANO Dehumidifier shows poor dew point performance, start by checking the inlet pressure; it should be a minimum of 4 barg. Adjust the inlet pressure settings if necessary. Ensure the power is on, the dryer front panel is illuminated, and the dryer is cycling correctly. If the desiccant is moist or contaminated, identify and eliminate the source of contamination and replace the cartridges, avoiding reuse. Confirm that the dryer's performance matches the required system air consumption. Verify the inlet air temperature against the technical specifications. Insufficient purge air can also cause this issue; consult service personnel to adjust the settings, as they are factory pre-set. Lastly, a blocked exhaust silencer may be the cause, requiring assistance from service personnel.
  • A
    Ashley GloverAug 28, 2025
    What to do if my NANO NDL-130 has constant depressurization?
    • K
      Kelly CopelandAug 28, 2025
      If your NANO Dehumidifier is constantly depressurizing, try switching it off and restarting it. Make sure the dryer is pressurized before powering it on to allow it to initialize before starting operation. Erratic airflow from the exhaust may indicate a faulty or damaged valve, requiring service.

Summary

General Information

General Safety

Provides critical safety information and warnings for product operation.

Technical Specification

Flow Rates

Details the flow rate specifications and pressure/temperature correction factors.

Operation

Guides on the proper procedures for starting and running the dryer.

Remote Start;Stop Control

Explains how to connect and utilize the remote start/stop functionality.

Remote Stop Control

Details the procedure for implementing a remote stop function for the dryer.

Shutdown Procedure

Outlines the steps for safely isolating and depressurizing the dryer.

Monitoring Dryer Performance (when ES option is fitted)

Adjusting Dewpoint Settings

Describes how to modify dewpoint set-points and alarm levels via the control panel.

Energy Saving Mode Active Display (ES Models)

Describes the display when the dryer is in energy saving mode.

Dew-point Sensor Fault Display (ES Models)

Indicates a fault with the dew-point sensor or its connection.

Dew-point Alarm Display (ES Models)

Energy Savings Adjustment Display (ES Models)

Maintenance

Service Schedule and Breakdown

Troubleshooting

Poor Dew-point Performance

Failure of Dryer to Cycle

NANO NDL-130 Specifications

General IconGeneral
ModelNDL-130
CategoryDehumidifier
Noise Level42 dB
Power Supply220-240 V, 50 Hz
Operating Temperature Range5°C - 35°C

Related product manuals