EasyManua.ls Logo

NANO NDL-2120 - User Manual

Default Icon
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
User guide
D3 heatless desiccant air dryer
revision: 2022-214 document: 17-100-0690
© 2022 Air & Gas Solutions LLC
www.n-psi.co.uk

Table of Contents

Other manuals for NANO NDL-2120

Preview: Maintenance Service Manual
Maintenance Service Manual24 pages

Questions and Answers

  • H
    Hannah SmithAug 10, 2025
    What to do if my NANO Dehumidifier fails to cycle?
    • J
      Jane PayneAug 10, 2025
      If your NANO Dehumidifier fails to cycle, there are several potential causes. First, ensure the controller is powered and check the on-screen column status to confirm it's powering the solenoid valves during normal operation. Also, verify the power to the unit and the fuse (T2A 250V). Insufficient inlet pressure (less than 4 barg) can also cause this issue, so adjust the inlet pressure settings if needed. If the unit fails to de-pressurize, the solenoid valve may not be functioning correctly; if there is power to the coil, replace the valve. Finally, check the inlet air supply if the outlet flow stops.
  • R
    Rhonda WalkerAug 17, 2025
    Why is my NANO Dehumidifier showing poor dew point performance?
    • B
      Brenda SmithAug 17, 2025
      Poor dew point performance in your NANO Dehumidifier can stem from several factors. Ensure the inlet pressure is at least 4 barg, adjusting the inlet pressure settings if necessary. An electrical fault could also be the cause, so ensure the power is on, the dryer front panel is illuminated, and the dryer is cycling correctly. Check for moist or contaminated desiccant; if present, eliminate the source of contamination and replace the cartridges. Also, verify that the dryer's performance matches the required system air consumption and check the inlet air temperature against the technical specifications. Insufficient purge air, which requires adjustment by service personnel, or a blocked exhaust silencer, also requiring service, could be responsible.
  • C
    Christopher GarrettAug 25, 2025
    What to do if my NANO NDL-2120 has constant depressurisation?
    • E
      Emily WeissAug 25, 2025
      If your NANO Dehumidifier is constantly depressurizing, try switching it off and restarting it. Ensure the dryer is pressurized before powering it on to allow it to initialize before commencing operation. Erratic airflow from the exhaust may also indicate a faulty or damaged valve, requiring service.
  • A
    adamnicholsonSep 1, 2025
    How to fix constant depressurization in NANO Dehumidifier?
    • C
      Connor RobinsonSep 1, 2025
      Constant depressurization in your NANO Dehumidifier can occur if the dryer fails to initialize. Try switching the dryer off and then restarting it. Ensure the dryer is pressurized before powering it on to allow proper initialization before operation. Erratic airflow from the exhaust may also indicate a faulty or damaged valve, requiring service.

Summary

Manufacturers Details and Support

General Safety

Safety precautions, regulations, and authorized personnel.

Intended Use of the Product

Dryer's intended use and location requirements.

Standard Controller Operations

Modbus Connection (ES Option)

Premium Controller Operations

Start-up and Operation

Remote Start;Stop Control

Wiring for remote start/stop functionality.

Emergency Stop Control

Wiring for emergency stop functionality.

Shutdown Procedure

Monitoring Dryer Performance (ES Option)

Monitoring performance and adjusting ES settings via HMI.

Maintenance

Service Schedule and Breakdown

Troubleshooting

Problem Diagnosis and Solutions

Common problems, causes, and solutions.

NANO NDL-2120 Specifications

General IconGeneral
BrandNANO
ModelNDL-2120
CategoryDehumidifier
LanguageEnglish

Related product manuals