NEC NP-PX700W Command Guide

======================================================================
Contents
1. Projector Control
2. Connection Method
3. Interface Conditions
4. List of Commands
5. Command Descriptions
6. Table of Response Error Codes
======================================================================
1. Projector Control
----------------------------------------------------------------------
NEC projectors make use of control commands that control the functions of the projector via connection with a
personal computer or another device.
======================================================================
2. Connection Method
----------------------------------------------------------------------
The following 3 kinds of connection methods are available for sending and receiving control commands.
1. Serial connection using the serial port on the projector
A serial cable is required.
2. USB connection using the USB port on the projector
A USB cable is required.
3. LAN connection
3-1. LAN connection using a wired LAN card
A wired LAN card and LAN cable are required.
3-2. LAN connection using a wireless LAN card
A wireless LAN card is required.
3-3.LAN connection using the LAN port on the projector
A LAN cable is required.
3-4. LAN connection using a wireless LAN unit
A wireless LAN unit is required
Status of supported connection
* A USB cable is supplied as standard with the MT860/1060/1065/1075.
* The GT5000/6000 does not come with a USB cable.
* Note that a connection method using the supplied USB cable is not supported for the LT220/240/260.
* The serial cable, LAN card and LAN cable are separately sold.
* The WT610 replaced the WT610 and uses the same command set.
(CAUTION)
Before making connections, be sure to invalidate the standby mode of the projector and set the "idle mode". The
projector cannot use the control commands in the standby mode.
Setting method: Under projector [Projector Options] --> [Setup], enter a check for [Idle Mode] on Page 4.
( CAUTION ) (!1)
Before making connections, be sure to select [NORMAL] for [STANDBY MODE].
Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL].
( CAUTION ) (!2)
The projector accept the "POWER ON" command during [POWER-SAVING] mode for[STANDBY MODE].
Supplement:
(!1) Only the NP600/NP610/NP3200 series is compatible.
(!2) Only the M300 series is compatible.

NEC NP-PX700W Specifications

General

Matrix size	0.65 \
Native aspect ratio	-
Projection distance	0.8 - 54.8 m
Vertical scan range	48 - 120 Hz
Horizontal scan range	15 - 108 kHz
Projection technology	DLP
Contrast ratio (typical)	2100:1
Screen size compatibility	50 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	- 30 - 30 °
Keystone correction, horizontal	- 40 - 40 °
Focal length range	26 - 117.4 mm
Aperture range (F-F)	1.7 - 3.1
Vertical lens shift range	-50 - 50 %
Horizontal lens shift range	-10 - 10 %
Lamp power	400 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Lamp power (economic mode)	320 W
Service life of light source	2000 h
Service life of light source (economic mode)	2500 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Audio (L/R) in	0
BNC input ports	5
USB connector type	USB Type-A
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Progressive scan output	Yes
VGA (D-Sub) ports quantity	3
Optical disc player type	Not included
Noise level	43 dB
Certification	USA: UL60950-1, FCC Part15 Class B, Canada: CSA60950-1, ICES-003 Class B
Noise level (economic mode)	39 dB
Placement	Desktop
Product type	Large venue projector
Product color	Black
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	33 W
Power consumption (typical)	1006 W
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR

Weight and Dimensions

Depth	516 mm
Width	504 mm
Height	192 mm
Weight	19700 g