NEC Univerge SV8100 - Page 75

UNIVERGE SV8100 Issue 1.0
System Maintenance Manual 3 - 35
+00 03 04 02 08 00 00 04
+0C 45 58 54 20 32 30 30
+20 20 20 20 20 1A 01 00
+05 01 01 13 01 01 21 01
+00 2E 01 00 3B 04 01 04
+00 00
response_while_frouting Selfport = 7c01 Target = 401 signal = 802
R ISDN : <<<<<<<<<<<<<<<<
16 0B A1 1F 01 01 00 USL(0,0),MESSAGE RECEIVED IND
08 02 80 08 20 Callref:DES(8),USER INFORMATION
A0 More data
7E 07 00 03 04 1B 00 00 User-user [7 octets]
+00
S ISDN : >>>>>>>>>>>>>>>>
14 A1 1F 01 01 00 USL(7,1),MESSAGE SEND REQ
08 02 00 08 20 Callref:ORG(8),USER INFORMATION
7E 07 00 03 04 1C 00 00 User-user [7 octets]
+00
R ISDN : <<<<<<<<<<<<<<<<
5A 0B A1 30 01 01 00 USL(0,0),SETUP CONF
08 02 80 08 07 Callref:DES(8),CONNECT
7E 4C 00 04 0C 45 58 54 User-user [76 octets]
+20 32 30 30 20 20 20 20
+20 1A 01 00 05 01 01 13
+01 01 21 01 00 2E 01 00
+3B 04 01 04 00 00 07 01
+01 02 01 01 24 01 02 2B
+11 11 00 00 00 00 00 00
+00 00 00 00 00 00 00 00
+00 00 0A 04 A2 0A 00 00
+03 04 10 08 00 00
response_while_frouting Selfport = 7c01 Target = 401 signal = 810
S ISDN : >>>>>>>>>>>>>>>>
0B A1 05 01 01 00 USL(7,1),SETUP COMPLETE REQ
08 02 00 08 0F Callref:ORG(8),CONNECT ACKNOWLEDGE
R ISDN : <<<<<<<<<<<<<<<<
1D 0B A1 09 01 01 00 USL(0,0),DISCONNECT IND
08 02 80 08 45 Callref:DES(8),DISCONNECT
08 02 80 90 Cause (16)
1E 02 81 82 Progress indicator
7E 07 00 03 04 04 08 00 User-user [7 octets]
+00
response_while_frouting Selfport = 7c01 Target = 401 signal = 804
S ISDN : >>>>>>>>>>>>>>>>
0F A1 0C 01 01 00 USL(7,1),RELEASE REQ
08 02 00 08 4D Callref:ORG(8),RELEASE
08 02 80 90 Cause (16)
R ISDN : <<<<<<<<<<<<<<<<
0C 0B A1 33 01 01 00 USL(0,0),RELEASE CONF
08 02 80 08 5A Callref:DES(8),RELEASE COMPLETE
CALLED clr_conf_system_id_on_cnetport() src_port=7c01
HP_LCD_REQ(0401,0001,0000,0000,0000)
ACD Data Size error. or socket close...
Networking procedure was not executed.