NETGEAR GS108LP Installation Guide

Installation Guide
April 2018
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
8-Port PoE/PoE+ Gigabit Unmanaged Switch
GS108LP and GS108PP
GS108LP
GS108PP
Package Contents
• Switch
• Power adapter
• Power cord (varies by region)
• Wall installation kit
• Rubber feet
• Rack-mount kit
• Installation guide
Step 1. Connect the equipment.
Step 2. Connect to power.
GS108LP
switch
Sample connections
Router
Internet
PoE+ security cameras
PoE+ access points
PoE VoIP phone
LED Status
PoE Considerations
The switch prioritizes the PoE and PoE+ power that it supplies in ascending port
order (from port 1 to port 8), with a total power budget of 120 watts. If the power
requirements for the attached powered devices (PDs) exceed the total power
budget of the switch, the PD on the highest-numbered port is disabled to make
sure that the PDs that are connected to the higher-priority, lower-numbered ports
are supported rst.
Just because a PD is listed as an 802.3at PoE powered device does not
necessarily mean that it requires the maximum power limit of the specication.
Many PDs require less power, allowing all eight PoE ports to be active
simultaneously.
The following table describes the PoE classes and switch allocations.
Device
Class
Standard Class
Description
Minimum Power
Allocated to the
Powered Device
Range of Power
Delivered to the
Powered Device
0 PoE and PoE+ Default
power (full)
0.44W 0.44W–12.95W
1 PoE and PoE+ Very low
power
4.0W 0.44W–3.84W
2 PoE and PoE+ Low power 7.0W 3.84W–6.49W
3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W
4 PoE+ only High power 30.0W 12.95W–25.5W
Power LED Left Port LEDs Right PoE LEDs
On
1000 Mbps link
PoE in use
Off
100 or 10 Mbps link
PoE halted (see PoE
Troubleshooting)
Activity (blinking)
No PoE use (off)
No link (off)
PoE Max LED
The maximum PoE power that the switch can deliver to all attached powered devices
(PDs) is 120 watts total, with a maximum power to each port of 30 watts. (For more
information, see PoE Considerations.)
The PoE Max LED indicates the status of the PoE power that the switch can deliver to
all attached PDs, as follows:
Solid amber. Less than 7W of PoE power is available on the switch.
Blinking amber. The PoE Max LED was lit solid in the previous two minutes.
Sufcient (more than 7W of) PoE power is available on the switch (the LED is
off).

NETGEAR GS108LP Specifications

General

Switch type	Unmanaged
Quality of Service (QoS) support	Yes
Power connector	AC-in jack
Gigabit Ethernet (copper) ports quantity	8
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	-
Form factor	1U
Product color	Black, Grey
Number of fans	0 fan(s)
Total Power over Ethernet (PoE) budget	60 W
Power source	DC/PoE
Input current	1.25 A
DC input voltage	54 V
Power consumption (max)	130 W
Power consumption (typical)	67.5 W
MAC address table	4000 entries
Mean time between failures (MTBF)	2752476 h
10G support	No
Networking standards	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Heat dissipation	230.85 BTU/h
Operating altitude	0 - 1000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	102 mm
Width	236 mm
Height	27 mm
Weight	600 g