NETGEAR MS510TX Installation Guide

Installation Guide
Congure the switch with a static IP address
Note: If your network uses a DHCP server, this section does not apply. Go
directly to Connect the switch to a network.
If you are using static IP addresses in your network, congure the switch IP
address before you connect the switch to a network.
1. Congure a computer with a static IP address in the 192.168.0.x subnet.
2. Plug the switch into a power outlet and connect your computer to the switch
using an Ethernet cable.
3. Open a web browser and enter 192.168.0.239 in the address bar.
The default IP address of the switch is 192.168.0.239.
A login page displays.
4. Enter password for the password.
The System Information page displays.
5. Select System > Management > IP Conguration.
The IP Conguration page displays.
6. Select the Static IP Address radio button.
7. Enter the static IP address, subnet mask, and default gateway IP address that
you want to assign to the switch.
8. Click the Apply button.
Your settings are saved.
Connect the switch to a network
1. Connect devices to the RJ-45 network ports on the switch front panel. For
model MS510TXPP only, you can connect PoE and non-PoE devices.
For 5G and 10G connections, use Cat 6, Cat 6a, or Cat 7 Ethernet cables
terminated with RJ-45 connectors.
2. Connect an RJ-45 port or SFP+ port on the switch to a network that includes
a DHCP server.
Note: In a small ofce or home ofce network, connect the switch to the LAN
port of a router that, in turn, is connected to an Internet modem.
If you use an SFP+ port, you must insert an SFP+ transceiver module, which is
available from NETGEAR.
NETGEAR 8-Port Multi-Gigabit Smart Managed Pro
Switch with two 10G Ports, Model MS510TX
NETGEAR 8-Port Multi-Gigabit Smart Managed Pro
Switch
with PoE+ and two 10G Ports, Model MS510TXPP
Package contents
• NETGEAR Smart Managed Pro Switch Model MS510TX or MS510TXPP
• AC power cord (localized to country of sale)
• Rubber footpads for tabletop installation
• 19-inch rack-mount kit for rack installation
• Installation guide
Note: For more information about installation, see the hardware installation
guide, which you can download from https://www.netgear.com/support/.
3. Power on the switch and wait two minutes.
Check the PoE status (MS510TXPP Only)
Model MS510TXPP can provide PoE+ power on ports 1–8. The switch can supply
up to 30W PoE+ (IEEE 802.3at) to each port, with a maximum PoE power budget
of 180W across all active PoE+ ports.
The PoE Max LED indicates the status of the PoE budget on the switch:
• Off. Sufcient (more than 7W of) PoE power is available.
• Solid amber. Less than 7W of PoE power is available.
• Blinking amber. At least once during the previous two minutes, less than 7W
of PoE power was available.
MS510TXPP
(PoE links for MS510TXPP only)
2.5G PoE link to WAC740
Sample connections
Internet
Core
switch
10G non-PoE uplink
5G non-PoE link to
two 2.5G servers
2.5G non-PoE
link to 2.5G NAS
2.5G non-PoE link to
2.5G gaming computer
Network router

NETGEAR MS510TX Specifications

General

Switch type	Managed
Switch layer	L2/L3/L4
Quality of Service (QoS) support	Yes
Stackable	-
Product color	Gray
Console port	RJ-45
USB 2.0 ports quantity	1
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Noise level	21 dB
Processor frequency	800 MHz
Mean time between failures (MTBF)	1078683 h
10G support	No
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Jumbo frames	10000
Latency (10 Gbps)	2.36 µs
MAC address table	16000 entries
Packet buffer memory	1.5 MB
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	26.1 W
Power consumption (typical)	10.19 W
DHCP features	DHCP client, DHCP server
Access Control List (ACL) rules	164
Heat dissipation	89.06 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Multicast MAC address table	512 entries

Weight and Dimensions

Depth	169 mm
Width	328 mm
Height	43 mm
Weight	1420 g