NETGEAR ProSAFE JGS516PE User Manual

350 East Plumeria Drive
San Jose, CA 95134
USA
August 2016
202-11700-01
ProSAFE® Gigabit Web Managed
(Plus) Switches
User Manual
GS105Ev2
GS105PE
GS108Ev3
GS108PEv3
GS116Ev2
JGS516PE
JGS524Ev2
JGS524PE

NETGEAR ProSAFE JGS516PE Specifications

General

Brand	NETGEAR
Model	ProSAFE JGS516PE
Category	Switch
Language	English

Summary

Manage Network Settings

Specify IP Address Settings for the Switch

Details how the switch obtains an IP address via DHCP or static configuration.

Use Browser-Based Access to Specify the Switch IP Address

Procedure to set the switch's IP address, subnet mask, and gateway via a web browser.

Use the ProSAFE Plus Utility to Specify the Switch IP Address

Steps to configure the switch's IP address using the ProSAFE Plus Configuration Utility.

Set Up Static Link Aggregation Groups

Use Browser-Based Access to Specify LAG Membership and Enable LAGS

Use the ProSAFE Plus Utility Specify LAG Membership and Enable LAGs

Optimize Performance With Quality of Service

Enable 802.1p/DSCP-Based Quality of Service

Explains how 802.1p/DSCP-based QoS prioritizes traffic based on packet header information.

Use Browser-Based Access to Enable 802.1p/DSCP-Based QoS

Instructions to enable 802.1p/DSCP-based QoS using a web browser interface.

Use the ProSAFE Plus Utility to Enable 802.1p/DSCP-Based QoS

Procedure to enable 802.1p/DSCP-based QoS using the ProSAFE Plus Configuration Utility.

Configure Port-Based Quality of Service

Describes how to assign priority to data passing through specific ports for faster transmission.

Use Browser-Based Access to Configure Port-Based QoS

Steps to configure port-based QoS priorities via a web browser.

Use the ProSAFE Plus Utility to Configure Port-Based QoS

Procedure to configure port-based QoS priorities using the ProSAFE Plus Utility.

Set Up Rate Limiting

Explains how to limit incoming and outgoing traffic rates per port.

Use Browser-Based Access to Set Up Rate Limiting

Instructions to configure ingress and egress traffic rates for ports via a web browser.

Use the ProSAFE Plus Utility to Set Up Rate Limiting

Procedure to configure ingress and egress traffic rates for ports using the ProSAFE Plus Utility.

Set Up Broadcast Filtering

Use Browser-Based Access to Set Up Broadcast Filtering

Use the ProSAFE Plus Utility to Set Up Broadcast Filtering

Use VLANS for Traffic Segmentation

Create Basic Port-Based VLANs

Use Browser-Based Access to Create Basic Port-Based VLANs

Use the ProSAFE Plus Utility to Create Basic Port-Based VLANs

Assign Ports to Multiple Port-Based VLANs

Use Browser-Based Access to Assign Ports to Multiple Port-Based VLANs

Use the ProSAFE Plus Utility to Assign Ports to Multiple Port-Based VLANs

Create 802.1Q-Based VLANs in a Basic Configuration

Explains creating 802.1Q-based VLANs with ID numbers for basic network segmentation.

Use Browser-Based Access to Create 802.1Q-Based VLANs in a Basic Configuration

Instructions to create basic 802.1Q VLANs via a web browser.

Use the ProSAFE Plus Utility to Create 802.1Q-Based VLANs in a Basic Configuration

Procedure to create basic 802.1Q VLANs using the ProSAFE Plus Utility.

Create 802.1Q-Based VLANs in an Advanced Configuration

Details advanced 802.1Q VLAN setup, including tagged/untagged ports and PVIDs.

Use Browser-Based Access to Create 802.1Q-Based VLANs in an Advanced Configuration

Steps to create advanced 802.1Q VLANs via a web browser.

Use the ProSAFE Plus Utility to Create 802.1Q-Based VLANs in an Advanced Configuration

Procedure to create advanced 802.1Q VLANs using the ProSAFE Plus Utility.

Add Tagged or Untagged Ports to an 802.1Q-Based VLAN

Explains how to add ports to an 802.1Q VLAN, specifying if they are tagged or untagged.

Use Browser-Based Access to Add Tagged or Untagged Ports to an 802.1Q-Based VLAN

Instructions to add tagged/untagged ports to 802.1Q VLANs via a web browser.

Use the ProSAFE Plus Utility to Add Tagged or Untagged Ports to an 802.1Q-Based VLAN

Specify a Port PVID for an 802.1Q-Based VLAN

Use Browser-Based Access to Assign a PVID to Ports

Use the ProSAFE Plus Utility to Assign a PVID to Ports

Manage and Monitor the Switch

Manage the Port Speed

Use Browser-Based Access to Specify the Port Speed or Shut Down a Port

Use the ProSAFE Plus Utility to Specify the Port Speed or Shut Down a Port

Enable Loop Detection

Use Browser-Based Access to Enable Loop Detection

Use the ProSAFE Plus Utility to Enable Loop Detection

Upgrade the Firmware

Information on checking for and upgrading the switch firmware to the latest version.

Use Browser-Based Access to Upgrade the Firmware

Instructions to upgrade switch firmware via a web browser.

Use the ProSAFE Plus Utility to Upgrade the Firmware

Procedure to upgrade switch firmware using the ProSAFE Plus Utility.

Save the Switch Configuration

Use Browser-Based Access to Save the Switch Configuration

Use the ProSAFE Plus Utility to Save the Switch Configuration

Restore a Saved Switch Configuration

Use Browser-Based Access to Restore a Saved Switch Configuration

Use the ProSAFE Plus Utility to Restore a Saved Switch Configuration

Restore Factory Default Settings

Details how to return the switch to its original factory default settings.

Use Browser-Based Access to Restore Factory Settings

Instructions to restore factory settings via a web browser.

Use the ProSAFE Plus Utility to Restore Factory Settings

Procedure to restore factory settings using the ProSAFE Plus Utility.

Diagnostics and Troubleshooting

Test Cable Connections

Use Browser-Based Access to Test a Cable Connection

Use the ProSAFE Plus Utility to Test a Cable Connection

Resolve a Subnet Conflict to Access the Switch

Guides on fixing subnet conflicts that prevent access to the switch.

Factory Default Settings

Table 1. Factory default settings