Newlong DS-9 - Machine Usage and Maintenance; Cautions When Using the Machine; Maintenance Procedures

Where
the construction
permits,
each
part
is stamped with
*lIft*fqfJ,EtlO;1H
its
part
number. On all orders,
please
include
part
number,
part
name
and
model name of rnachine.
o
=z*vYfT#(ffi)
AElEffiffilaitDs-9d)ftfi8*fJ#
tffi.{ffiL<*c9*f.
Safety
Rules
To
prevent
personal
injury:
.
:'tstOffiil.
zt*)!xl'Ozi*)*ElAf6(lffim
o
All
power
sources to the machine
must
be
turned offbefore
(li'3V
t.
threading,
oilins, adjusting or
replacing
parts.
o
{Effi
l:j6
EE
/r,F.X.
${EE
+
a)&HtT.#/r,f;
.
t
o
A1l
cover
and
guards
must
be
in
position
before
operating
D{&#lffitf
Etfi49
lc(
V
t
&6^lJ.
f.
H
L
\Ilf
L
tfcld*
machine.
*Llc.=,,.-vYr''f#(*)eEig*6trl.aB*F<fl3
u\"
BitDm,ffiffi*. ffiffi66.
ii/)/@fi5#.
:i/)/
t
Do
not
tamper
with
safety
cover,
guards,
etc.,
while
6ts4:ffim(ld8t,t*f&)*sffiV'.'vtlcL*-d-"
maehllre
is
in operation.
ldentifying ond Ordering
Pqrls
Coulions
When Using
ihe Mochine
Mqintenonce
tt-
t'xr:EEf
6 fjF6L\et
EHl'OtrH
gffi
Safety Precautions tA{:eUtf
1)Always turn
po$rer
off
before threadins, oilins, and
1)f;E=#X9'iAEJtLatZDXiiEL,
X\D*&,ffi&.ffi#.
adjusting the
machine
or replacins
parts.
*tJffit&. {*+,f;&{f#a-ffii.Z,fE,ffi&9lc((Id3
l/\"
2) Wear safety
srasses.
2)ffi*{F#0>}SEAAlrrz^alFHt*;ffDLEf"
3) Make
sure, before starting the machine,
that
all covers
3)A(O#'iz\-itZ'fIEEBfrlaffiD((fl5v''"
and shields are in
place
and closed.
4) Do not touch
on
the
machine when it
is run.
4)
f
zr*fta*iiffiEa(lrr6:LAffiffiL(r)BiEEL(<
fd8u."
5)
Turn
power
off
and make sure the cutter
does
not operate
5)
ffl)Tla+b^tLbL*lt.
/'f€rHt9]-a((Idttr
''"
before
you put your
fingers
under the
cutter blades
and
l6E.ffi*.Ctelt.
Z.f€ffitgJ0:yy7)rfi7)r/3trta|
the needles to adjust.
&ffiffiL(i.btF#.t'fr">((ld3tr\"
6) Do
not
touch on the machine
when
it is run. 6):y)/OiEE$lclt.
iyyl.mful31ta47351rt"
o
Please keep in mind to handle the machine
carefirlly and to
o
iyvEF*t5ltffiffi/ed.3/e*Ilffii.bH*trrr<L\*f.
maintain the machine in
good
condition.
ilHW<&$RiL&6tlHt:Effitl,L.fSiJ((li3V',.
o
Thread tuzz or
dust
must be cleaned with air
or brush on
o
-
E
A+FXrtrK-f
L*Llcb.
fi+ffi"D k,
*9&.0>l#0>
throat
plate,
in the
groove
of feed dog
or
around
looper
F,
tL-z{*a*bDIaR*aftl8LDS}*B*t,U\la}fi'9
after
the day's work.
ffiL\(T$L\"
o
Wipe
the area easy to rust with
oil cloth.
.
ZD{frffiDL\ffiEtr}*lH&'gaffiVt((fd8Vl"
o
Check the machine for loose screws and tighten
them,
if
o
E
lc-Eltt-rDffi.\fiiltL\r\,F,ffrL((ld3v''.
any,
once a month,
o
Good maintenance
will
prolong
the machine life.
o
+y'.fi,ORLHLttt#ffia#frIc**#L*fOfa'igH
(li8v''"