To Next Page

To Previous Page

11 – English

5.1 - Insights on certain programmable functions and options

5.1.1 - Dip-switches 1 and 2 (for the Stop input)

3GDRDCHORVHSBGDR@QDTRDCSNOQNFQ@LLDSGD2SNOHMOTSNMSGDA@RHRNESGDSXODNER@EDSXCDUHBDBNMMDBSDC

"NMS@BSVHSGJ´jWDCQDRHRS@MBDVHSGHMUDQRHNM

"NMS@BSVHSGJ´jWDCQDRHRS@MBDVHSGNTSHMUDQRHNM

- NO (normally open) contact.

- NC (normally closed) contact.

5.1.2 - Dip-switch 5 (for the SbS input)

(ESGD2A2HMOTSHROQNFQ@LLDCVHSGSGDRSDOAXRSDORDPTDMBDNEBNLL@MCR> Open > Stop > (again...)SGDQDENQDVHSGCHORVHSBGRDSSN

ON, during use of the automation it will not be possible to command the closing of the door. This command can only be given by programming

the automatic re-closing (dip-switch 8 set to ON), or through a radio transmitter.

5.1.3 - Dip-switch 6

• During an opening manoeuvre: if the condominium function is enabled (dip-switch 6 set to ON), it prevents the stoppage of the manoeuvre

after an opening or step-by-step command is sent, or its inversion prior to terminating at the limit switch.

• During a closing manoeuvre: if the condominium function is enabled (dip-switch 6 set to ON), the sending of an opening or step-by-step

command stops the manoeuvre and inverts its movement, making the door open.

5.2 - Memorisation of the dip-switch settings

After setting all the dip-switches (or later on, whenever the user wishes to modify the setting of one or more dip-switches), it is necessary to

LDLNQHRDSGDRDSSHMFRHMSGDBNMSQNKTMHSHMSGDENKKNVHMFV@XVGDMSGDq2.r/('RS@QSRk@RGHMFFQDDMQDCHSLD@MRSG@SNMDNQLNQDCHO

switches has been shifted. Therefore, to memorise the new setting press and hold button T1 on the control unit, until the q2.r/(' remains

steady lit green. Subsequently, release the button.

5.3 - Programming the “Work TimerRIWKHPRWRUDQGWKHqPause TimerIRUDXWRPDWLFUHFORVLQJ

3GDf6NQJ3HLDt@MCSGDf/@TRD3HLDtare two basic parameters of the control unit and are programmed one after the other, with the same

procedure. These parameters can only be programmed once all the dip-switches have been set and memorised.

s:KDWLVWKHq:RUN7LPHr"(SHRSGDL@WHLTLCTQ@SHNMENQVGHBGSGDBNMSQNKTMHSJDDORSGDLNSNQONVDQDCEQNLSGDSHLD@BNLL@MCHRRDMS

This duration must be long enough for the motor to complete the manoeuvre (up to the limit switch). The default setting (or after the memory

HRETKKXCDKDSDCHRRDBNMCR'NVDUDQSGHRU@KTDB@MADLNCHjDCAXOQNFQ@LLHMF@CTQ@SHNMNERDBNMCRLHMHLTLTOSNRDBNMCR

L@WHLTL3GDOQNBDCTQDDMS@HKRLD@RTQHMFSGDSHLDlHMRDKEQDBNFMHSHNMLNCDlQDPTHQDCENQSGDLNSNQSNBNLOKDSD@L@MNDTUQD%NQSGHR

reason it is necessary to measure the most strenuous manoeuvre for the gate (i.e. the slowest one), which normally corresponds to the start of

Nice MC200 Instructions And Warnings For Installation And Use

Other manuals for Nice MC200