What to do if data is not printed on Nidek Medical LM-7 Measuring Instruments?
If data is not printing, check the printer paper to ensure it hasn't run out and load new paper if needed. Also, verify that the Printer parameter is not set to 'Off' and reset it if necessary.
How to fix Nidek Medical LM-7 Measuring Instruments when the LCD does not turn on?
If the LCD isn't turning on, ensure the power cord is securely connected. Also, check that the power switch is turned on.
Why does the display of the LCD suddenly disappear on Nidek Medical LM-7 Measuring Instruments?
The display might disappear suddenly because the display auto off function is activated. Press the touch screen to exit from auto off mode.
What to do if the position touched on the screen and the response position do not match on Nidek Medical LM-7 Measuring Instruments?
If the touched position on the screen doesn't match the response position, perform a calibration for the touch screen.
What to do if the LCD does not turn on (or is unclear) even though the power is on for Nidek Medical LM-7?
If the LCD doesn't turn on (or is unclear) even with the power on, the display auto off function may be activated. Press the touch screen to exit from auto off mode. Alternatively, the brightness may be set too low, so check the setting of the Contrast parameter.
What to do if the printer does operate, however, printed results cannot be obtained from Nidek Medical LM-7?
If the printer operates but no results are printed, the printer paper may be loaded with the wrong side up. Load the printer paper with the correct side up.
Why data cannot be written even though the Eye Care card is inserted in Nidek Medical LM-7 Measuring Instruments?
Data might not be written to the Eye Care card because the contacts in the Eye Care card slot may be soiled. Clean them. Also, if an error occurs while data is read in the other device such as a refractor, clean its card reader.
How to fix communication issues with a computer on Nidek Medical Measuring Instruments?
If communication with a computer is not possible, the User name, Domain, PC name, or Folder parameter may be set incorrectly. Check whether any unnecessary character, space, or symbol is entered.
General| Brand | Nidek Medical |
|---|---|
| Model | LM-7 |
| Category | Measuring Instruments |
| Language | English |
Instructions to read the operator's manual before device operation for safety and procedures.
Guidelines for safe and proper operation, handling of power, and environmental considerations.
Explanation of labels and symbols used on the device for user attention and identification.
Overview of the NIDEK AUTO LENSMETER LM-7/LM-7P and its intended use.
Detailed description of the device's parts and components, including pilot lamp, touch screen, and buttons.
Explanation of the different measurement screens, their areas, and interactive elements.
List of items included in the standard configuration of the device for user verification.
Initial setup procedures including cable connection, startup, and basic configuration settings.
Overview of the device's operational workflow from turning on to turning off.
Steps for performing pre-use checks and powering on the device for measurement.
Instructions for correctly setting uncut, mounted, and contact lenses on the nosepiece.
Procedure for measuring single vision lenses, including alignment and reading data.
Method for measuring bifocal and trifocal lenses, including distance and near portions.
Procedure for measuring progressive power lenses, covering distance and near zone measurements.
Method for measuring prism power on mounted lenses for strabismus and phoria prescriptions.
Steps for measuring contact lenses, including setting and alignment on the nosepiece.
Procedure for measuring UV transmittance of lenses, including comparison and correction.
How to use the scale mode for measuring PD, LPD/RPD values by aligning glasses to the screen scale.
Procedure for marking the optical center and axis direction on lenses for precise measurements.
Instructions for printing measured data, including sample printouts and output options.
Method for saving measured data to an Eye Care card for data transfer and management.
Procedures for turning off the device and protecting it with a dust cover after operation.
Guidelines for connecting and operating peripheral devices like printers, computers, and refractors.
Comprehensive guide to all device parameters, their functions, and how to adjust them.
Table of common symptoms and their remedies to resolve device issues before contacting support.
List of error messages displayed on the screen and the corresponding solutions for troubleshooting.
Procedure for calibrating the touch screen if the response position does not match the touch point.
Steps for replacing the printer paper when it runs short or a red line appears.
Instructions for replacing the ink cartridge or supplying ink to the ink pad when markings become faint.
Procedure for adjusting the feel of the lens table lever movement for optimal operation.
Guidelines for cleaning the device exterior, protective glass, printer, and Eye Care card slot contacts.
List of consumables and replacement parts for the device, including part numbers and appearance.
Detailed technical specifications for measurement items, ranges, accuracy, and functions.
Glossary of terms and abbreviations used throughout the Operator's Manual for clarity.
Information regarding electromagnetic compatibility, emissions, immunity, and specified cables.
To Next Page