What to do if squeegee lift linkage arm/knob doesn’t raise or lower squeegee on Nilfisk-Advance Floor Machine?
If the squeegee lift linkage arm/knob doesn’t raise or lower the squeegee, it could be due to a worn cable bushing under the eyelet of the squeegee cable in the steering column, or a bent/sheared weldment linkage because the squeegee lift cable is too tight. Follow the instructions in the “Squeegee Lift Cable Adjustment - ST” section.
Why squeegee lift linkage arm keeps bending on Nilfisk-Advance Advenger BR 855 Floor Machine?
If the squeegee lift linkage arm at the steering column of your Nilfisk-Advance Floor Machine keeps bending or breaking, it's likely that the squeegee lift cable is too tight. You should follow the instructions in the “Squeegee Lift Cable Adjustment - ST” section.
Why squeegee lift linkage arm doesn't raise squeegee on Nilfisk-Advance Floor Machine?
If the squeegee lift linkage arm or knob on your Nilfisk-Advance Floor Machine isn’t raising or lowering the squeegee, the cable bushing under the eyelet of the squeegee cable in the steering column may be worn. Alternatively, the weldment linkage could be bent or sheared because the squeegee lift cable is too tight. To resolve this, follow the instructions in the “Squeegee Lift Cable Adjustment - ST” section.
What to do if lift motor doesn't run on Nilfisk-Advance Floor Machine?
If the lift motor on your Nilfisk-Advance Floor Machine doesn't run and the display shows an error fault code, it indicates a lift motor electrical system failure. Refer to the chart in the “Main Controller Error Codes” for service actions.
How to adjust squeegee tips on Nilfisk-Advance Advenger BR 855 Floor Machine?
To resolve squeegee tips being driven into the floor with your Nilfisk-Advance Floor Machine, adjust the squeegee using the adjustment knob, turning it clockwise to raise the tips.
What to do if squeegee is hopping on Nilfisk-Advance Advenger BR 855?
To address a squeegee that is “hopping” on your Nilfisk-Advance Floor Machine, reposition the wheel in the slot on the squeegee tool to ensure it makes contact with the floor. Refer to the “Squeegee Adjustments” section.
Why is there not enough adjustment of squeegee tool by turning adjustment knob on Nilfisk-Advance Advenger BR 855?
If there is not enough adjustment of the squeegee tool when turning the adjustment knob, the squeegee mount weldment bracket may be bent. Replace it.
How to fix squeegee hopping on Nilfisk-Advance Floor Machine?
If the squeegee is hopping, it may be because the wheel isn’t making contact with the floor. Reposition the wheel in the slot on the squeegee tool. Refer to the “Squeegee Adjustments” section.
Why lift motor runs in both directions but does not raise or lower the squeegee tool assembly on Nilfisk-Advance Advenger BR 855?
The lift motor may run in both directions without raising or lowering the squeegee tool assembly because the threads in the moveable lift motor assembly drive tube are damaged (stripped), or the lift cable is damaged (stretched or broken).
What to do if lift motor does not run and the display shows an error fault code on Nilfisk-Advance Advenger BR 855?
If the lift motor doesn't run and the display shows an error fault code, it indicates a lift motor electrical system failure. Please, refer to chart in “Main Controller Error Codes” for service actions.
Essential safety guidelines to prevent injury and machine damage.
Step-by-step guide on starting, operating, and stopping the machine.
Explanation of controls, buttons, and display indicators on the main panel.
Procedures for aligning and adjusting squeegee tilt and wheel height for optimal performance.
Detailed steps for removing and replacing the squeegee lift actuator.
Detailed steps for removing the brush motor from the disc scrub deck assembly.
Instructions for removing and replacing the vacuum motor assembly.
Procedure for removing and replacing the solution solenoid valve.
Common problems and solutions related to the wheel drive system and motor.
Step-by-step guide for removing and installing the drive wheel assembly.
Technical details on control board connector pinouts for diagnostic testing.
Guide to accessing and using Service Test Mode for troubleshooting components.
A comprehensive checklist for performing preventive maintenance tasks on the machine.
General| Brand | Nilfisk-Advance |
|---|---|
| Model | Advenger BR 855 |
| Category | Floor Machine |
| Language | English |
To Next Page