Nilfisk-Advance CR 1200

Other manuals for Nilfisk-Advance CR 1200

Quick Start Manual76 pages

Quick Start Troubleshooting Manual83 pages

Mechanical Repair Service Manual54 pages

Questions and Answers

A
Audrey PierceAug 19, 2025
What to do if there is inadequate or no solution flow in my Nilfisk-Advance Scrubber?
- M
  Michael JosephAug 19, 2025
  If your Nilfisk-Advance Scrubber isn't dispensing enough solution, or no solution at all, several factors could be at play. First, ensure the solution tank is adequately filled. Next, verify that the main solution flow control valve lever is set to the 'on' position. A clogged solution filter, valves, or hoses can also impede flow, so inspect and clear any obstructions. If these steps don't resolve the issue, the solution solenoid valve (L1) might be defective and require replacement. Finally, a solution system fault in the main controller A1* could be the cause, so it should be checked for faults.
P
pevansAug 21, 2025
Why is my Nilfisk-Advance Floor Machine tripping the circuit breakers?
- M
  mary30Aug 22, 2025
  Your Nilfisk-Advance Floor Machine might be tripping the circuit breakers due to several reasons: * An electrical short circuit. It is suggested to have your Nilfisk Service Center or qualified electrician check the machine. * An overloaded or jammed shaker motor. Check the shaker motor. * Debris wrapped around the broom drive. Remove the debris. * The side broom is set too low. Adjust the side broom. * An overloaded or jammed hopper. Check the hopper. * An overloaded or jammed power steering unit. Check the power steering unit.
S
Susan WeberAug 25, 2025
What to do if my Nilfisk-Advance Floor Machine will not move?
- S
  spencerstacyAug 25, 2025
  If your Nilfisk-Advance Floor Machine won't move, consider these possible causes: 1. The parking brake might be set. Release the parking brake. 2. A circuit breaker might be tripped. Reset any tripped circuit breakers. 3. The battery stop plate might not be installed. Install the battery stop plate. 4. The seat switch might be defective. Replace the seat switch.
K
Kristina MyersAug 26, 2025
How to improve poor water pickup on Nilfisk-Advance Floor Machine?
- C
  Carolyn GonzalezAug 26, 2025
  If you're experiencing poor water pickup with your Nilfisk-Advance Floor Machine, here are some potential causes and solutions: * Worn or torn squeegee blades: Reverse or replace them. * Squeegee out of adjustment: Adjust it so the blades touch the floor evenly across the entire width. * Recovery tank full: Empty the recovery tank. * Open recovery tank drain hose: Secure the drain hose cap or replace it. * Recovery tank cover gasket leak: Replace the gasket. * Debris caught in squeegee: Clean the squeegee. * Vacuum hose clogged: Remove the debris. * Using too much solution: Adjust the solution control valve.
M
Michelle WilsonAug 27, 2025
Why won't the main broom run on my Nilfisk-Advance Floor Machine?
- S
  Steven CrossAug 27, 2025
  The main broom on your Nilfisk-Advance Floor Machine may not run for the following reasons: * Debris is wrapped around the broom drive. Remove the debris. * The hopper is not completely down. Lower the hopper completely. * A circuit breaker has tripped. Reset any tripped circuit breakers.
D
danielorozcoAug 29, 2025
How to fix poor sweeping performance on Nilfisk-Advance Floor Machine?
- L
  lonnieclarkAug 29, 2025
  If your Nilfisk-Advance Floor Machine has poor sweeping performance, check these: * Broom out of adjustment: Adjust the broom. * Hopper full: Empty the hopper. * Broom bristles worn or curved: Replace or rotate the broom. * Broom housing skirts damaged or worn: Replace the skirts.
M
Michelle TuckerAug 31, 2025
How to troubleshoot inadequate solution flow in Nilfisk-Advance Floor Machine?
- P
  Paul PierceAug 31, 2025
  If you're experiencing inadequate solution flow in your Nilfisk-Advance Floor Machine, consider the following: * Not using enough solution: Adjust the solution control valve. * Solution tank empty: Fill the solution tank. * Solution lines or valves clogged: Flush the lines and valves. * Solution control valve not open: Adjust the solution control valve. * Solution switch OFF: Turn ON the solution switch.
H
Heidi SchmidtSep 2, 2025
What causes side brooms to not run on a Nilfisk-Advance Floor Machine?
- C
  Cody CooleySep 3, 2025
  The side brooms on your Nilfisk-Advance Floor Machine may not run due to: * Debris wrapped around the broom drive. Remove the debris. * The hopper not being completely down. Lower the hopper completely. * A tripped circuit breaker. Reset any tripped circuit breakers.
C
Charles CooperSep 4, 2025
How to improve the scrubbing performance of my Nilfisk-Advance Floor Machine?
- K
  Karen HenrySep 4, 2025
  To improve the scrubbing performance of your Nilfisk-Advance Floor Machine, consider these points: * Brush bristles worn or curved: Rotate or replace the brushes. * Moving machine too fast: Slow down. * Not using enough solution: Adjust the solution control valve.
M
Mike DaySep 6, 2025
Why don't the vacuum motors run on my Nilfisk-Advance Floor Machine?
- M
  Megan NealSep 7, 2025
  If the vacuum motors on your Nilfisk-Advance Floor Machine aren't running, it could be due to: * A tripped circuit breaker. Reset any tripped circuit breakers. * The recovery tank being full. Empty the recovery tank.