Nobles SpeedGleam - User Manual

Other manuals for Nobles SpeedGleam

Operator's Manual29 pages

Specifications1 page

Questions and Answers

H
heidiandersonAug 15, 2025
What to do if my Nobles Floor Machine has no power?
- J
  Jack MunozAug 16, 2025
  If your Nobles Floor Machine has no power, there might be several reasons. First, check if the main power circuit breaker has tripped; if so, determine the cause and reset it. Ensure the battery charger is disconnected. If your machine has an emergency stop button, make sure it is not activated by turning the button to reset it. Also, check for loose battery cables and tighten them if necessary. If all of these are correct, you may need to replace faulty batteries.
H
Heidi BuckleyAug 18, 2025
Why does my Nobles SpeedGleam have a short run time?
- C
  Carla WilliamsAug 18, 2025
  If your Nobles Floor Machine has a short run time, ensure that the batteries are fully charged. If the issue persists, a battery cell may be defective and require replacement. Also, a faulty battery charger can cause short run times, so consider replacing the charger.
P
Pamela ArnoldAug 21, 2025
What to do if the pad motor does not operate on my Nobles SpeedGleam Floor Machine?
- U
  ueverettAug 21, 2025
  If the pad motor on your Nobles Floor Machine isn't working, first check if the pad motor circuit breaker has tripped. If it has, replace the pad or adjust the pressure, then reset the breaker. You can also replace the 2A fuse. Also, ensure the machine is not tilted back on its rear wheels; lower it from the tilt position if it is.
M
Megan GuzmanAug 25, 2025
What to do if my Nobles SpeedGleam Floor Machine does not propel?
- S
  Shawn JohnsAug 25, 2025
  If your Nobles Floor Machine isn't moving, make sure the operator is seated in the seat. Also, check that the seat sensor wire harness plug is connected.
J
James JohnsonAug 27, 2025
What to do if the vacuum motor does not operate on my Nobles Floor Machine?
- W
  William WongAug 27, 2025
  If the vacuum motor on your Nobles Floor Machine isn't working, reset the circuit breaker button on the vacuum.
M
Michael WeaverAug 30, 2025
What to do if the battery charger will not operate for my Nobles SpeedGleam?
- J
  john69Aug 30, 2025
  If the battery charger for your Nobles Floor Machine isn't working, replace the charger fuse if it's blown.
P
pperrySep 3, 2025
How to fix a Nobles SpeedGleam Floor Machine when the burnishing head will not lower or raise?
- L
  Linda ClarkSep 3, 2025
  If the burnishing head on your Nobles Floor Machine isn't lowering or raising, make sure you press the 1--STEP button. Also, recharge the batteries, as the low voltage interrupter may be activated.
A
Amanda ReedSep 5, 2025
What to do if I am unable to change burnishing settings on my Nobles SpeedGleam?
- M
  martinjessicaSep 5, 2025
  If you're unable to change the burnishing settings and the lockout light is blinking on your Nobles Floor Machine, contact your supervisor.
M
maxwelllarsonSep 8, 2025
Why does my Nobles SpeedGleam have no power?
- D
  Donna PowellSep 8, 2025
  If your Nobles Floor Machine has no power, here are a few things to check: * Ensure the battery charger is disconnected. * If equipped, verify the emergency stop switch is not activated; turn the button to reset it. * Check for a tripped main circuit breaker and reset it after determining the cause. * Inspect the battery cables for looseness and tighten them if necessary. If these steps don't resolve the issue, the batteries might be faulty and need replacement.
B
Brandi EdwardsSep 12, 2025
What to do if the pad motor does not operate on Nobles Floor Machine?
- H
  Henry AllenSep 12, 2025
  If the pad motor on your Nobles Floor Machine isn't working, it could be due to a tripped pad motor circuit breaker. Try replacing the pad or adjusting the pressure, then reset the breaker. Also, check if the tilt safety switch is activated or faulty; if so, lower the machine from the tilt position.

Summary

Machine Data

Safety Precautions

Machine Components Overview

Machine Installation Procedures

Installing Machine Batteries

Detailed steps and safety warnings for installing the batteries.

Machine Setup and Configuration

Installing the Burnishing Pad

Machine Operation Guide

Pre-Operation Checklist

Burnishing Operation (2510 Model)

Specific instructions for operating the 2510 model for burnishing.

Burnishing Operation (2550 Model)

Safe Operation Practices

Emergency Stop Switch Operation

Circuit Breaker Reset

Battery Charging Procedures

Machine Maintenance Schedule

Daily Maintenance Tasks

Battery Maintenance Guide

Transporting the Machine

Troubleshooting Common Issues

Machine Specifications

SpeedGleam Wiring Diagram

SpeedGleam Ladder Diagram

SpeedGleam Plus Wiring Diagram

SpeedGleam Plus Ladder Diagram

Hour Meter, Emergency Stop, and Keyswitch Kits

Parking Brake Kit

Flashing Light Kit

Nobles SpeedGleam Specifications

Engine Specifications

transport mode	Pad assist forward motion
pad motor	3 hp, 2.24 kW
pad motor speed	2000 rpm - nominal load / 2500 rpm - no load

Power

battery capacity	215 AH
battery voltage	12 V
charging unit description	36 V DC, 25 A

Operating Environment

pad pressure	Variable; 15-45 lb / 7-20 kg
maximum coverage rate per hour	21, 000 ft²/h / 1951 m²/h
burnish width	20 in / 508 mm
sound level at operator’s ear	70 dBa

Weight and Dimensions