Why is the water flow insufficient in my Oase Water Filtration System?
Several factors can cause insufficient water flow in your Oase Water Filtration System. The impeller unit, foam filter, filter media, or pipework might be soiled and require cleaning. The inlet strainer could be clogged and needs to be cleaned. The impeller unit may be worn and need replacement. Ensure that the water flow is correctly set.
What to do if my Oase Water Filtration System does not start up?
If your Oase Water Filtration System doesn't start, first check the mains voltage. If the voltage is ok, the impeller unit might be blocked and needs cleaning. Another cause could be air trapped inside the filter, in this case, vent the filter by moving it from side to side to release any trapped air.
How to improve the filtering performance of my Oase Water Filtration Systems?
Poor filtering performance in your Oase Water Filtration System can stem from a soiled or worn foam filter in the pre-filter, or from soiled or worn filter media in the filter unit. Clean soiled components or replace worn ones to restore optimal performance.
Why is the water heating insufficient in my Oase BioMaster Thermo 350 Water Filtration Systems?
If your Oase Water Filtration System (with heater) isn't heating water sufficiently, the heater may be defective and require replacement, or it may not be calibrated correctly and need calibration. Also, ensure the water temperature is correctly set on the heater. Insufficient water flow can also cause this issue; refer to the troubleshooting steps for 'Water flow insufficient'.
How to reduce noise from my Oase Water Filtration System?
Increased noise in your Oase Water Filtration System is often due to air trapped in the filter. To resolve this, move the filter from side to side to allow the remaining air to escape.
What to do if the Oase Water Filtration System cannot be vented?
If you're unable to vent your Oase Water Filtration System, the valve box in the pre-filter may be blocked and require cleaning. Also, ensure the filter is installed below the surface of the water.
How to fix Oase Water Filtration Systems unit that does not start up?
If your Oase Water Filtration System unit doesn't start, begin by verifying the mains voltage. If the voltage is correct, check for blockages in the impeller unit and clean it if necessary. Air trapped in the filter can also prevent startup; vent the filter by moving it from side to side to release any trapped air.
What to do if my Oase BioMaster Thermo 350 Water Filtration Systems has insufficient filtering performance?
If your Oase Water Filtration System isn't filtering effectively, the foam pre-filter or the filter media in the container might be soiled. Clean them. If cleaning doesn't improve performance, consider replacing these components, as they may be worn.
Why the Oase BioMaster Thermo 350 Water Filtration Systems filter cannot be vented?
If your Oase Water Filtration System filter cannot be vented, the valve box in the pre-filter may be blocked, so you should clean the valve box. Also, ensure that the filter is installed below the water's surface.
How to reduce increased noise in Oase BioMaster Thermo 350 Water Filtration Systems?
If your Oase Water Filtration System is making more noise than usual, there might be air trapped inside the filter. Try moving the filter from side to side to help release any remaining air.
General| Flow Rate | 1100 L/h |
|---|---|
| Suitable for Aquariums up to | 350 liters |
| Integrated Heater | Yes |
| Heater Power | 200 W |
| Weight | 6.5 kg |
| Hose Diameter | 16/22 mm |
| Suitable for Freshwater | Yes |
| Suitable for Saltwater | Yes |
| Filter Type | External Filter |
Specifies the intended application and operational restrictions for the unit.
Explains how water flows through the filter pathways and heating system.
Lists all components included in the package for the BioMaster and BioMaster Thermo models.
Provides safety instructions for handling the hot heater to prevent burns or glass breakage.
Details the steps to safely remove the heater for cleaning or maintenance.
Explains the procedure for correctly installing the heater into the adapter.
Describes how to detach the connection unit for cleaning or maintenance.
Outlines the steps to properly attach the connection unit to the filter head.
Details the process for detaching the pre-filter for cleaning or maintenance.
Explains how to correctly re-attach the pre-filter to the unit head.
Provides instructions for removing the unit head for filter media changes.
Guides the user on how to properly reassemble the unit head after maintenance.
Instructs on how to attach the rubber feet to the base of the filter unit.
Advises on thoroughly rinsing filter media before first-time use to remove soiling.
Explains how to add an OASE HeatUp heater to non-Thermo models.
Details how to assemble the inlet assembly for water intake.
Describes how to set up the outlet assembly using spray bars or water distributor.
Explains the procedure for connecting the inlet and outlet tubing to the unit.
Guides on how to remove trapped air from the filter system for proper operation.
Provides instructions for safely powering on the filter unit and heater.
Details the correct procedure for disconnecting the unit and heater from power.
Explains how to adjust the water flow rate using the lever on the connection unit.
Provides steps to clean or replace the foam filters located in the pre-filter.
Details the process for cleaning or replacing the filter media within the main filter unit.
Explains how to clean or replace the impeller unit for optimal pump performance.
Describes how to clean the valve box if venting issues persist after cleaning foams.
Details cleaning the suction chamber, warning about spring tension.
Lists components that are considered wear parts and are excluded from the warranty.
Provides information on obtaining original OASE spare parts for continued operation.
Explains the meaning of various symbols found on the unit for user guidance.
To Next Page