EasyManua.ls Logo

OHAUS Catapult 1000 - User Manual

OHAUS Catapult 1000
2 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Quick Start Guide Catapult 1000
Ohaus Corporation www.ohaus.com i Catapult 1000 Scales Quick Start Guide
PREPARATION FOR USE
Check Power
If using AC power, be sure local line voltage
matches voltage printed on the scale’s power
adapter. If not, do not use AC power.
Connect adapter plug to input jack at rear.
To use battery power, remove battery cover
and insert three LR14 (“C”) batteries.
Allow at least five minutes warm-up time,
for scale to stabilize before operation.
SELECTING THE LOCATION:
Place on a firm, steady surface with sufficient space.
Avoid excessive air current, vibrations, heat sources, or rapid temperature changes.
SAFETY PRECAUTIONS
For dependable operation of this product, observe the following precautions:
• Verify that the input voltage printed on the power Adapter and the plug type
matches the local power supply (if using AC power).
• Make sure that the power cord does not pose an obstacle or tripping hazard.
• Disconnect the product from the power supply when cleaning.
• Do not operate this product in hazardous or unstable environments.
• Do not drop loads on the pan.
• Use only approved accessories and peripherals, as available.
• Operate the product only under ambient conditions specified in the Instruction
Manual.
• Service should be performed by authorized personnel only.
Power Input Jack

Other manuals for OHAUS Catapult 1000

Preview: Service Manual
Service Manual34 pages

Questions and Answers

  • S
    scottmichelleAug 17, 2025
    Why my OHAUS Catapult 1000 Scales will not turn on?
    • T
      Tracy LamAug 17, 2025
      If your OHAUS Scales won't turn on, there are a couple of things to check: * **Power Source:** Make sure the scale is properly connected to a power source and that the voltage is correct. Try connecting the power and replacing the batteries. * **Battery Condition:** If you're using battery power, the batteries might be drained. Try replacing them.
  • J
    Jesse McbrideAug 19, 2025
    What to do if my OHAUS Catapult 1000 Scales display -E-?
    • A
      Andrea GutierrezAug 20, 2025
      If your OHAUS Scales display '-E-', it means the scale is overloaded. Remove some weight from the platform.
  • T
    Timothy TranAug 22, 2025
    What to do if OHAUS Scales display 000000 or 999999 or no weight reading?
    • M
      Michelle CastilloAug 22, 2025
      If your OHAUS Scales display '000000' or '999999', or there is no weight reading, it could be due to: * **Load Cell Cable:** The load cell cable may be disconnected. Connect the load cell cable to the scale and then calibrate the scale. * **Calibration Data:** There might be no calibration data in the EEPROM. Connect the load cell cable to the scale and then calibrate the scale.
  • J
    Joshua BakerAug 26, 2025
    How to improve accuracy of OHAUS Catapult 1000?
    • N
      Nicole HoldenAug 26, 2025
      If your OHAUS Scales are showing poor accuracy, it might be due to: * **Calibration:** The scale may need to be calibrated. Perform a calibration. * **Environment:** The scale could be in an unstable environment. Move it to a more suitable, stable location.
  • K
    Kevin ClineAug 28, 2025
    Why I am unable to calibrate my OHAUS Catapult 1000 Scales?
    • J
      Jason FryeAug 28, 2025
      If you're unable to calibrate your OHAUS Scales, consider these potential causes: * **Environment:** An unstable environment can interfere with calibration. Move the scale to a stable location. * **Calibration Mass:** Using the wrong calibration mass can also cause issues. Ensure you are using the correct calibration mass.
  • C
    Courtney SimpsonAug 30, 2025
    What does CALE mean on OHAUS Catapult 1000 Scales?
    • W
      wandersonAug 30, 2025
      If your OHAUS Scales display 'CALE', it indicates a calibration error. Stop the calibration process, check that you are using the correct weight, and then try again.
  • J
    James JenkinsSep 2, 2025
    What does -A- mean on OHAUS Scales?
    • T
      Tammy PatelSep 2, 2025
      If your OHAUS Scales display '-A-', it means the scale is in Dynamic Weighing Mode. If you want to exit, remove the mass from the platform and press UNITS Cal.
  • W
    wrightcharlesSep 5, 2025
    What does UnSt mean on OHAUS Catapult 1000 Scales?
    • E
      Erica JonesSep 5, 2025
      If your OHAUS Scales display 'UnSt', it means the scale was unstable at power on. Make sure the environment is stable, the scale is on a flat surface, and check the adjustable feet.
  • F
    fcoxSep 8, 2025
    What does Lo bat OFF mean on OHAUS Catapult 1000 Scales?
    • G
      Gregory FrostSep 8, 2025
      If your OHAUS Scales display 'Lo bat OFF', it means the scale shut down due to low battery. Replace the batteries.
  • L
    leesamanthaSep 12, 2025
    What does Lo Line OFF mean on OHAUS Catapult 1000?
    • V
      vgouldSep 12, 2025
      If your OHAUS Scales display 'Lo Line OFF', it indicates a low line voltage shutdown, which is a power adapter problem. If the input voltage is unstable, try switching to battery operation.

Summary

Preparation For Use

Check Power

Verifies power connection and warm-up requirements for the scale.

Selecting The Location

Safety Precautions

Controls Overview

Button Functions

Explains the purpose and operation of each button on the scale.

Operation Guide

Power On and Zeroing

Details how to turn the scale on, zero it, and tare.

Overload and Auto Shut-Off

Information on overload indication and automatic power off.

Dynamic Weighing

Instructions for using the scale's dynamic weighing feature.

OHAUS Catapult 1000 Specifications

General IconGeneral
BrandOHAUS
ModelCatapult 1000
CategoryScales
LanguageEnglish

Related product manuals