What to do if the browser version is old for Oki C9000?
If you encounter issues related to an old browser version with your Oki Printer, ensure you are using either: * Internet Explorer 5.5 or higher (open the browser, then select [About Internet Explorer] in the [Help] menu) * Netscape Navigator version 6 or higher (open the browser, then select [About Netscape] in the [Help] menu).
What to do if the certificate is created, but SSL/TLS is turned off on Oki C9000?
If the certificate is created, but SSL/TLS is turned off on your Oki Printer, change the setting for SSL/TSL to ON. Using the web browser: 1. Open the browser and type in the print server’s IP Address, then press the Enter key. 2. Login. 3. On the [Security] tab, click [Cipher (SSL/TLS)] 4. Change the setting to [SSL/TLS] to ON and click [Submit]. Using AdminManager: 1. Launch the AdminManager utility and login. 2. Click the printer in the list, then click [Setup] ? [OKI Device Setup]. 3. Enter your password, click [OK]. 4. Click the [SSL/TLS] tab. 5. Make sure the box next to [Use Cipher(SSL/TLS)] is checked. 6. Close the utility.
Why Oki C9000 does not print?
If your Oki Printer does not print, verify the following: * Make sure the network cable is correctly connected; if it is, try changing it. * Turn the printer off and on again. * Ensure the NIC is connected to the File Server. * Confirm that the printer driver has been mapped to the correct NetWare queue.
How to fix Error writing to Prn1 on Oki C9000?
If you receive an 'Error writing to Prn1' message on your Oki Printer, here are a few things to check: * Make sure the printer is online. * If the error indicates a paper shortage, add more paper and cancel the error. * Check if another user is currently printing; if so, wait until they are finished before printing.
How to fix PostScript error occurs if a banner page is printed on Oki Printer?
If a PostScript error occurs when printing a banner page on your Oki Printer, turn the banner output Off in the client’s printer settings.
How to fix EEPROM Check registers NG on Oki Printer?
If you encounter an 'EEPROM Check registers NG' error on your Oki Printer, try the following: * Confirm that the NIC is installed correctly, and then turn the printer off and on again. * Initialize the NIC.
What to do if NG is printed in the Self-diagnostic test of Oki Printer?
If 'NG' is printed during the Self-diagnostic test on your Oki Printer, take these steps: * Confirm that the NIC is installed correctly, and then turn the printer off and on again. * Ensure the network cable is correctly connected. * Connect to a different network segment and rerun the test to see if this resolves the problem.
How to fix cannot print with lpr and ftp on Oki Printer?
To fix printing issues with lpr and ftp on your Oki Printer, follow these steps: * Turn the printer off and on again. * Make sure there is a response to the ping command. * Ensure the network cable is correctly connected, and try changing it if necessary. * Make sure the host name and IP address are configured in the workstation. * Ensure the printer port name is configured in the workstation. * Use 'lp' as the default port name, as 'euc' and 'sjis' are specific to printers with PostScript available.
What to do if Oki C9000 Printer network interface card is not identified?
To resolve the issue of your Oki Printer's network interface card not being identified, consider the following steps: * Turn the printer off and on again. * Ensure the network cable is correctly connected. Try changing the cable to rule out a cable issue. * Confirm that [Microsoft network client] and [NetBEUI] have been added to the network section of the control panel. * Verify that the NetBEUI protocol is set to Enable. * Make sure the factory setting of the workgroup name is PrintServer and the computer name is ML+ the last six digits of the MAC address. * Ensure the computer name of the NIC is different from the computer name on the network.
How to fix Oki Printer cannot find the network print server?
If your Oki Printer cannot find the network print server, try the following: * Turn the printer off and on again. * Confirm that the network interface is enabled on the printer. * Make sure the network cable is correctly connected. If it is, try changing the cable. * If the NetWare protocol is disabled, set it to Enable. * Reset the network interface card to factory default settings.
To Next Page
General
