Olympus IPLEX IV9420RT User Manual (English)

Questions and Answers:

S
Shannon HenrySep 7, 2025
How to improve image brightness on my Olympus Analytical Instruments?
- N
  Natasha CastroSep 7, 2025
  If the image brightness is not optimum on your Olympus Analytical Instruments, configure the proper setting by performing the [BRT] lever operation. Check if the objective lens on the insertion tube's distal end or the optical adapter is dirty and clean it. Also, ensure that the external monitor is correctly adjusted and the optical adapter is properly attached. If the optical adapter is old, consider replacing it.
S
Sheri HarrisAug 23, 2025
What to do if I see a 'LOW BATTERY' message on my Olympus Analytical Instruments?
- D
  Dr. Melissa McclainAug 23, 2025
  If you see a 'LOW BATTERY' message on your Olympus Analytical Instruments, immediately stop any image recording, copying, USB formatting, or deleting operations. Replace the battery or connect the AC adapter to continue using the instrument.
C
Christopher CarlsonAug 25, 2025
Why my Olympus Analytical Instruments system cannot be turned on?
- C
  Cheryl BenjaminAug 26, 2025
  If the system cannot be turned on, ensure the AC adapter or battery is correctly connected. Also, verify that you are pressing the power button on the main unit. If it still fails to turn on, check that you are using the designated AC adapter or battery for the Olympus Analytical Instruments.
D
david01Aug 26, 2025
What to do if my Olympus Analytical Instruments shows 'RECORDING MEDIA FULL'?
- S
  Steven AdamsAug 26, 2025
  To address a 'RECORDING MEDIA FULL' error on your Olympus Analytical Instruments, delete any unnecessary data from the USB flash drive to free up space. Alternatively, replace the current USB flash drive with a new one.
R
Rhonda BradleyAug 27, 2025
What to do if Olympus Analytical Instruments shows 'IMAGE CAPTURE ERROR'?
- C
  Charles ParrishAug 27, 2025
  If you encounter an 'IMAGE CAPTURE ERROR' on your Olympus Analytical Instruments, stop the inspection and turn the instrument off, then turn it on again.
E
Edwin WolfAug 29, 2025
What to do if Olympus Analytical Instruments shows 'HIGH TEMPERATURE (MAIN UNIT)'?
- R
  robert45Aug 29, 2025
  If you see a 'HIGH TEMPERATURE (MAIN UNIT)' message on your Olympus Analytical Instruments, it indicates the main unit is overheating. Stop the inspection, allow the instrument to cool down, and then turn the power back on.
R
Robert MartinezSep 8, 2025
What to do if Olympus Analytical Instruments shows 'IMAGER ERROR'?
- J
  Jesse SnyderSep 8, 2025
  If you encounter an 'IMAGER ERROR' on your Olympus Analytical Instruments, stop the inspection and turn the instrument off, then on again.
L
Lindsay CarlsonSep 5, 2025
Why is the illumination not working on my Olympus Analytical Instruments?
- R
  Renee StephensSep 5, 2025
  If the illumination on your Olympus Analytical Instruments does not light up, first ensure the LIGHT button is turned on. If it still doesn't work, check if the insertion tube's distal end or the optical adapter is dirty and wipe it with a clean piece of gauze or cotton swab. You can also use a brush to remove any foreign matter.
B
Benjamin FletcherSep 3, 2025
What to do if Olympus Analytical Instruments shows 'HIGH TEMPERATURE (DISTAL END)'?
- A
  Amy BlackSep 3, 2025
  If you get a 'HIGH TEMPERATURE (DISTAL END)' message on your Olympus Analytical Instruments, immediately pull the insertion tube out of the observation object.
M
Michael WilliamsSep 4, 2025
What to do if my Olympus Analytical Instruments says 'NO RECORDING MEDIA'?
- W
  williamsjuliaSep 4, 2025
  If your Olympus Analytical Instruments displays 'NO RECORDING MEDIA', load the USB flash drive and try again. If the problem persists, turn the instrument off, then on again.