Olympus IPLEX FX IV8000-2

Questions and Answers

A
April MillerAug 17, 2025
What to do if I get a 'RECORDING MEDIA ERROR' on my Olympus IPLEX FX IV8000-2?
- E
  eugene44Aug 18, 2025
  If you receive a 'RECORDING MEDIA ERROR' message, it means that the recording media is either not formatted or the data you're trying to access is damaged. To resolve this, format the recording card or USB memory using the IPLEX FX.
R
Robert ParkerAug 20, 2025
Why does my Olympus IPLEX FX IV8000-2 display a message when using battery?
- N
  Nathan WhiteAug 20, 2025
  The message appears because the battery voltage has dropped. To fix this, immediately stop recording, copying, moving, deleting images, or formatting recording media and quickly replace the battery. Alternatively, plug in the adapter.
B
brenda50Aug 22, 2025
How to fix ERROR (AD1) on Olympus Analytical Instruments?
- C
  Christopher BrownAug 22, 2025
  ERROR (AD1) indicates an abnormality in the scope tip electrode or optical adapter electrode. Immediately withdraw the scope from the object of observation and turn the power off. Clean the scope tip and optical adapter electrodes, and then reinstall the optical adapter.
S
Sandra TaylorAug 25, 2025
Why does the self-check trigger during use and display a message on my Olympus Analytical Instruments?
- J
  John Vargas DDSAug 26, 2025
  This occurs because heat has built up inside the base unit, triggering the self-check function. Terminate the inspection, allow the instrument to cool down, and then turn the power back on again. If you are using battery power, replace the battery.
C
carol68Aug 27, 2025
Why DETAIL image cannot be recorded or retrieved on Olympus Analytical Instruments?
- D
  davidpughAug 27, 2025
  The internal memory card is not formatted or the data being accessed is damaged. Try again, or turn power off and then back on again.
S
Shelia PerryAug 30, 2025
What does 'RECORDING MEDIA NOT READY' mean on my Olympus IPLEX FX IV8000-2 and how do I fix it?
- J
  Jason HowardAug 30, 2025
  The message 'RECORDING MEDIA NOT READY' means that you tried to access the recording media without any inserted, or the recording media was removed during operation. Insert a recording card or USB memory to use and restart operation.
J
Joseph PotterSep 1, 2025
Why am I getting a message while increasing the light emitted by the scope on my Olympus Analytical Instruments?
- P
  powersdanielSep 1, 2025
  The distal end of the scope is hot. Wait until the scope distal end cools before using it.
A
Andrew MooreSep 4, 2025
What does ERROR (D1) mean on my Olympus Analytical Instruments?
- J
  Jeffrey PowersSep 4, 2025
  ERROR (D1) means that the self-check function is activated and urges termination of inspection. Stop inspection and turn the instrument off then on again.
L
lewiskathySep 7, 2025
Why is the angulation operation extremely heavy on my Olympus IPLEX FX IV8000-2 Analytical Instruments?
- R
  robertmartinezSep 7, 2025
  The insertion tube is overloaded and the self- check function was triggered to prompt termination of inspection. Extend the insertion tube as much as possible to reduce the loop amount, and turn power back on without operating the [ANGLE] joystick.
M
Mr. Jacob CummingsSep 9, 2025
What does it mean when a message appears when the scope is inserted into a high-temperature observation object with Olympus IPLEX FX IV8000-2 Analytical Instruments?
- J
  Jo MillerSep 9, 2025
  The message informs you that the self-check function was triggered to prompt termination of inspection. Immediately pull the scope out of the observation object.