What to do if Olympus Analytical Instruments shows 'IMAGER ERROR'?
If you encounter an 'IMAGER ERROR' on your Olympus Analytical Instruments, stop the inspection and turn the instrument off, then on again.
How to improve image brightness on my Olympus Analytical Instruments?
If the image brightness is not optimum on your Olympus Analytical Instruments, configure the proper setting by performing the [BRT] lever operation. Check if the objective lens on the insertion tube's distal end or the optical adapter is dirty and clean it. Also, ensure that the external monitor is correctly adjusted and the optical adapter is properly attached. If the optical adapter is old, consider replacing it.
What to do if I get an 'OVER CURRENT (USB)' error on my Olympus Analytical Instruments?
To resolve the 'OVER CURRENT (USB)' error on your Olympus Analytical Instruments, first, power off the instrument and then turn it back on. Ensure you are using a recommended USB flash drive. If the issue persists, disconnect all USB devices except the flash drive, as other connected devices might be causing the overcurrent.
What to do if my Olympus Analytical Instruments says 'NO RECORDING MEDIA'?
If your Olympus Analytical Instruments displays 'NO RECORDING MEDIA', load the USB flash drive and try again. If the problem persists, turn the instrument off, then on again.
What to do if Olympus Analytical Instruments shows 'HIGH TEMPERATURE (DISTAL END)'?
If you get a 'HIGH TEMPERATURE (DISTAL END)' message on your Olympus Analytical Instruments, immediately pull the insertion tube out of the observation object.
What to do if I get a 'RECORDING MEDIA ERROR' on my Olympus Analytical Instruments?
To resolve a 'RECORDING MEDIA ERROR' on your Olympus Analytical Instruments, format the USB flash drive directly on the instrument.
How to fix a blurry image on my Olympus Analytical Instruments?
If the image from your Olympus Analytical Instruments is not sharp, try wiping the objective lens on the insertion tube's distal end or the optical adapter with a clean piece of gauze or a cotton swab. Ensure the optical adapter is properly attached and that the external monitor is correctly adjusted.
Why is the operation load for articulation getting heavier on my Olympus Analytical Instruments?
If you are experiencing heavy operation load for articulation with your Olympus Analytical Instruments, the angulation lock might be engaged. Press down the [ANGLE LOCK] lever to release the angulation lock.
What to do if Olympus Analytical Instruments shows 'HIGH TEMPERATURE (MAIN UNIT)'?
If you see a 'HIGH TEMPERATURE (MAIN UNIT)' message on your Olympus Analytical Instruments, it indicates the main unit is overheating. Stop the inspection, allow the instrument to cool down, and then turn the power back on.
What to do if Olympus Analytical Instruments shows 'IMAGE CAPTURE ERROR'?
If you encounter an 'IMAGE CAPTURE ERROR' on your Olympus Analytical Instruments, stop the inspection and turn the instrument off, then turn it on again.
Lists critical safety guidelines for handling the instrument, covering usage environments and operational warnings.
Guides users through initial steps, including preparing the power supply (battery or AC adapter).
Covers essential pre-use procedures like attaching the optical adapter, powering on, and checking the battery level.
Outlines a checklist for inspecting the instrument before and after use to identify any abnormalities.
Explains how to turn on illumination, insert the tube, and control angulation for observation.
Covers functions for freezing images, zooming, and adjusting image brightness and display modes.
Details how to switch GAIN modes and adjust image brightness using the BRT lever.
Explains the process of preparing the USB flash drive and specifying recording settings for still and movie images.
Guides on how to display recorded images in full-screen or thumbnail views and navigate through them.
Provides steps for preparing and displaying PDF files on the instrument's screen.
Details how to navigate and select options within the instrument's menu system using the joystick.
Illustrates the sequence of steps for performing stereo measurements, from adapter attachment to value checking.
Details the procedure for confirming measurement accuracy before and after operations.
Offers guidance on resolving common issues and interpreting error messages displayed by the instrument.
Specifies the recommended operating temperatures, humidity, and liquid resistance for the instrument.
General| Brand | Olympus |
|---|---|
| Model | IPLEX IV9420RT |
| Category | Analytical Instruments |
| Language | English |
To Next Page