EasyManua.ls Logo

omi EL 72 - User Manual

Default Icon
69 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OMI srl
Cod. 710.0151.01.00 Rev0B – 08.2012
- I -
ESSICCATORI D’ARIA COMPRESSA AD ESPANSIONE DIRETTA
Manuale d’ uso e manutenzione
- GB -
DIRECT EXPANSION COMPRESSED AIR DRYERS
Instruction and Maintenance Manual
- D -
DRUCKLUFT KÄLTETROCKNER
Handbuch für Betrieb und Wartung
- F -
SECHEUR D’AIR A EXPANSION DIRECTE
Manuel d’instructions et d’entretien
- E -
SECADORES A EXPANSIÓN DIRECTA
Manual de uso y mantenimiento
- RUS -
ОСУШИТЕЛИ СЖАТОГО ВОЗДУХА РАСШИРИТЕЛЬНОГО ТИПА
Руководство по эксплуатации и техническому обслуживанию
EL
36 – 54 – 72 – 108 – 144
180 – 216 – 280 – 340

Table of Contents

Questions and Answers

  • W
    William ChavezAug 20, 2025
    What to do if my omi Dehumidifier has water in the system?
    • R
      Ryan GeorgeAug 20, 2025
      If you find water in the system, start by restoring power to the line. Next, check the cabling and replace if faulty. Inspect the electronic control board and replace it if problems persist. Ensure the dryer is turned on by pressing the ON/OFF switch. Wait two minutes after turning the dryer on. Verify the compressed air inlet/outlet is connected properly. Restore nominal conditions if the air flow rate, temperature, or ambient temperature are too high. Clean the condenser and the condensate drainage system pre-filter. Replace the coil of the drainage solenoid valve if burned, or clean/replace the valve if clogged. Check the C8 and C9 parameters on the electronic control board and replace if necessary. Finally, check and replace the temperature control probe if faulty.
  • M
    masonsarahAug 30, 2025
    Why is there water in my omi EL 72 system?
    • J
      julie06Aug 30, 2025
      There are several possible reasons for water in the system. These include: a lack of power, cabling problems, issues with the electronic control board, the dryer being off or in standby, incorrect connection of the compressed air inlet/outlet, air flow/temperature or ambient temperature exceeding nominal values, a dirty condenser, a malfunctioning condensate drain, a burned coil or clogged drainage solenoid valve, or a faulty temperature control probe. The C8 and C9 parameters of the electronic control board could also be the reason.
  • D
    davissarahNov 9, 2025
    How to fix water in omi Dehumidifier system?
    • M
      Melanie KramerNov 9, 2025
      If there's water in the system, several factors could be responsible. First, ensure power is available. Then, examine the cabling and replace it if necessary. Inspect the electronic control board and replace it if needed. Confirm the dryer is on and not in standby mode (wait 2 minutes after switching on). Check that the compressed air inlet/outlet is correctly connected. Also, make sure that the air flow rate and temperature entering the dryer are within nominal values, as well as the ambient temperature. Clean the condenser and the condensate drainage system pre-filter. Consider replacing the coil or cleaning/replacing the drainage solenoid valve if burned or clogged. Finally, check the C8 and C9 parameters of the electronic control board and replace it if the issue continues. Check the t...

Summary

1. General Information

1.1 Functional Description

Explains the operational principle and features of the air dryer.

1.2 Safe Use of the Dryer

Covers safety guidelines and compliance with European directives for operation.

2. Installation

3. Start Up

3.1 Control Panel

Overview of the dryer's control panel, including keys, display, and LEDs.

3.1.1 Keys Function

3.1.2 Condensate Discharge Parameters Programming

3.1.3 Anomaly Warning

3.2 Before Start Up

3.3 Start Up

4. Maintenance, Troubleshooting and Dismantling

4.1 Maintenance

4.2 Troubleshooting

4.3 Dismantling

C) Data Sheet

D) Basic Spare Parts

omi EL 72 Specifications

General IconGeneral
Brandomi
ModelEL 72
CategoryDehumidifier
LanguageEnglish

Related product manuals