What to do if my Omnik Omniksol-17k-TL2 shows a GFCI Device Fault?
If your Omnik Inverter displays a 'GFCI Device Fault', it could be due to an issue with the inverter's GFCI detector. First, try restarting the inverter to see if that clears the fault. If the problem continues, try re-flashing the software. If neither of these steps works, the part or the entire inverter may need to be replaced.
How to fix PV Volt High on Omnik Inverter?
If your Omnik Inverter is showing a 'PV Volt High' error, it means the DC voltage is too high because of incorrect installation. To resolve this, correct the installation by removing panels. If the issue persists, try re-flashing the software. As a last resort, you may need to replace a part or the entire inverter.
How to resolve PV Volt Low error on Omnik Omniksol-17k-TL2 Inverter?
If your Omnik Inverter shows a 'PV Volt Low' error, it indicates that the DC voltage is below 150V. To fix this, correct the installation by adding more panels. If the problem continues, try re-flashing the software. If that doesn't work, you may need to replace a part or the inverter.
What to do if Omnik Inverter shows No Utility error?
If your Omnik Inverter displays a 'No Utility' error, it means there is no AC voltage. Use a multimeter to measure the AC voltage and check the wires in the AC cable to ensure they are properly connected.
Why is my Omnik Inverter showing an Island Fault?
An 'Island Fault' on your Omnik Inverter means there's no grid or the local grid frequency isn't stable. Restart the inverter after ensuring the local grid is stable. Alternatively, you can close the protection from the inverter.
How to fix Ground Current Fault on Omnik Omniksol-17k-TL2 Inverter?
If your Omnik Inverter displays a 'Ground Current Fault', it's often due to poor grounding or can occur on rainy days. Ensure the inverter is well-grounded. You can also change it to another standard with wider protection range under authorization.
What causes Bus Volt High on Omnik Omniksol-17k-TL2?
If your Omnik Inverter displays a 'Bus Volt High' error, it could be due to a wrongly test value, a software issue, or broken hardware. First, try restarting the inverter to check if that clears the fault. If the problem continues, try re-flashing the software. If neither of these steps works, the part or the entire inverter may need to be replaced.
What does Bus Volt Low mean on Omnik Omniksol-17k-TL2 Inverter?
If your Omnik Inverter displays a 'Bus Volt Low' error, it could be due to a wrongly test value, a software issue, or broken hardware. First, try restarting the inverter to check if that clears the fault. If the problem continues, try re-flashing the software. If neither of these steps works, the part or the entire inverter may need to be replaced.
What does Consistency Fault mean on Omnik Omniksol-17k-TL2 Inverter?
If your Omnik Inverter displays a 'Consistency Fault', it indicates an inconsistency in the data detected by the master and slave CPUs. Try restarting the inverter to see if that resolves the issue. If the problem persists, try re-flashing the software. If neither works, consider replacing the part or the entire inverter.
What causes Bus Unbalance error on Omnik Omniksol-17k-TL2?
If your Omnik Inverter displays a 'Bus Unbalance' error, it could be due to an inverter control circuit problem or the values of two rows bus capacitance differ too much. Try restarting the inverter. If the problem continues, try re-flashing the software. If neither of these steps works, the part or the entire inverter may need to be replaced.
Explains DANGER, WARNING, CAUTION, and NOTICE symbols for hazard identification.
Crucial safety warnings for electrical shock and installation procedures.
Detailed explanation of symbols found on the inverter for clear understanding.
Comprehensive technical specifications for Omniksol inverter models.
Critical safety warnings and environmental considerations for inverter installation.
Essential safety warnings regarding electrical connections and compliance.
Instructions and warnings for connecting DC power from PV modules.
Guidance on AC wiring, including wire gauge and protective devices.
Lists and describes various fault states that the inverter may encounter.
Steps for configuring the WiFi card to connect to a wireless network.
Lists common fault codes, their possible causes, and recommended solutions.
General| Model | Omniksol-17k-TL2 |
|---|---|
| Type | Grid-tied Inverter |
| Rated Output Power | 17000 W |
| Max. DC Voltage | 1000 V |
| Number of MPPTs | 2 |
| Max. AC Power | 17000 W |
| THDi | <3% |
| Power Factor | >0.99 |
| Max. Efficiency | 98.2% |
| DC Connection | MC4 |
| Protection Degree | IP65 |
| Cooling Method | Natural convection |
| AC Output Frequency | 50/60 Hz |
| Nominal AC Voltage | 400 V |
| Operating Temperature Range | -25°C to +60°C |
| AC Output Voltage | 400 V |
To Next Page