Main circuit
22
■Recommended Wire Diameter, Wiring Tools, and Crimping Terminals
200V class
Note 1. The wire diameter described in the above table shows the design value of the HIV line (heat-resistant 75 °C) standard.
2. When connecting wires to the main circuit terminal block, use the Round crimp terminal (UL compliant product) suitable for the
wire used. Crimp terminals should be crimped using the Crimping tool recommended by the crimping terminal manufacturer.
Model
3G3RX2
Rated
settings
Power line
AWG (mm
2
)
R, S, T, U, V, W, P,
PD, N
Ground line
AWG (mm
2
)
Braking resis-
tor AWG
between
P and RB (mm
2
)
Screw size
of power
line terminal
Crimping terminal
power line/ground
line
Tightening
torque N·m
A2004
ND
14 (2.1) 14 (2.1) 14 (2.1) M4 2-4/2-4 1.4LD
VLD
A2007
ND
14 (2.1) 14 (2.1) 14 (2.1) M4 2-4/2-4 1.4LD
VLD
A2015
ND
14 (2.1) 14 (2.1) 14 (2.1) M4 2-4/2-4 1.4LD
VLD
A2022
ND
14 (2.1) 14 (2.1) 14 (2.1)
M4
2-4/2-4
1.4LD
VLD 10 (5.3) 10 (5.3) 10 (5.3) 5.5-4/5.5-4
A2037
ND
10 (5.3) 10 (5.3) 10 (5.3) M4 5.5-4/5.5-4 1.4LD
VLD
A2055
ND
8 (8.4) 8 (8.4) 8 (8.4) M5 8-5/8-5 3.0LD
VLD
A2075
ND
8 (8.4)
6 (13.3)
8 (8.4)
M5
8-5/8-5
3.0LD
VLD 6 (13.3) 6 (13.3) 14-5/8-5
A2110
ND 6 (13.3)
6 (13.3)
6 (13.3)
M6
14-6/14-6
4.0LD
4 (21.2) 4 (21.2) 22-6/14-6
VLD
A2150
ND 4 (21.2)
6 (13.3)
4 (21.2)
M6
22-6/14-6
2.5 to 3.0LD
3 (26.7) 3 (26.7) 38-6/14-6
VLD
A2185
ND 3 (26.7)
6 (13.3)
3 (26.7)
M6
38-6/14-6
2.5 to 3.0LD 2 (33.6) 2 (33.6)
VLD 1 (42.4) 1 (42.4) 60-6/14-6
A2220
ND 1 (42.4)
6 (13.3)
1 (42.4)
M8
60-8/14-6
5.5 to 6.6LD 1/0 (53.5) 1/0 (53.5)
VLD 2/0 (67.4) 2/0 (67.4) 70-8/14-6
A2300
ND 2/0 (67.4)
4 (21.2) --- M8
70-8/22-8
6.0LD
1/0×2 (53.5×2) 60-8/22-8
VLD
A2370
ND 4/0 (107.2)
4 (21.2) --- M8
100-8/22-8
15.0LD
1/0×2 (53.5×2) 60-8/22-8
VLD
A2450
ND
1/0×2 (53.5×2)
4 (21.
2) --- M
8
60-8/22-8
6.0 to 10.0LD
VLD 2/0×2 (67.4×2) 70-8/22-8
A2550
ND 350kc (177)
3 (26.7) --- M10
180-10/38-8
19.6LD
3/0×2 (85.0×2) 80-10/38-8
VLD
To Next Page
Loading...
Need help?
General