Related Manuals
22
NJ-series Troubleshooting Manual (W503)
NJ-series Troubleshoot-
ing Manual
W503 NJ501-@@@@
NJ301-@@@@
Learning about the
errors that may be
detected in an NJ-series
Controller.
Concepts on managing errors that may be detected
in an NJ-series Controller and information on individ-
ual errors are described.
Use this manual together with the NJ-series CPU
Unit Hardware User’s Manual (Cat. No. W500) and
NJ-series CPU Unit Software User’s Manual (Cat.
No. W501).
CJ-series Special Unit
Manuals for NJ-series
CPU Unit
W490
W498
W491
Z317
W492
W494
W497
W495
W493
CJ1W-@@@@ Learning how to use CJ-
series Units with an NJ-
series CPU Unit.
The methods and precautions for using CJ-series
Units with an NJ501 CPU Unit are described, includ-
ing access methods and programming interfaces.
Manuals are available for the following Units.
Analog I/O Units, Insulated-type Analog I/O Units,
Temperature Control Units, ID Sensor Units, High-
speed Counter Units, Serial Communications Units,
DeviceNet Units, EtherNet/IP Units, and CompoNet
Master Units.
Use these manuals together with the NJ-series CPU
Unit Hardware User’s Manual (Cat. No. W500) and
NJ-series CPU Unit Software User’s Manual (Cat.
No. W501).
Sysmac Studio Version 1
Operation Manual
W504 SYSMAC-
SE2@@@
Learning about the
operating procedures
and functions of the
Sysmac Studio.
Describes the operating procedures of the Sysmac
Studio.
CX-Integrator
CS/CJ/CP/NSJ-series
Network Configuration
Tool Operation Manual
W464 Learning how to config-
ure networks (data links,
routing tables, Commu-
nications Unit settings,
etc.).
Describes operating procedures for the CX-Integra-
tor.
CX-Designer User’s
Manual
V099 Learning to create
screen data for NS-
series Programmable
Te r m in al s.
Describes operating procedures for the CX-
Designer.
CX-Protocol Operation
Manual
W344 Creating data transfer
protocols for general-
purpose devices con-
nected to CJ-series
Serial Communications
Units.
Describes operating procedures for the CX-Protocol.
GX-series EtherCAT
Slave Unit User’s Manual
W488 GX-ID@@@@
GX-OD@@@@
GX-OC@@@@
GX-MD@@@@
GX-AD@@@@
GX-DA@@@@
GX-EC@@@@
XWT-ID@@
XWT-OD@@
Leaning how to connect
GX-series EtherCAT
Slave Units.
Provides the specifications of and descr
ibes applica-
tion methods for GX-series EtherCAT Slave Units.
MX2/RX Series Inverter
EtherCAT Communica-
tion Unit User’s Manual
I574 3G3AX-MX2-
ECT
3G3AX-RX-ECT
Leaning how to connect
a 3G3AX-MX2-ECT or
3G3AX-RX-ECT Ether-
CAT Communications
Unit for MX2/RX-series
Inverters.
Describes the following information for the 3G3AX-
MX2-ECT and 3G3AX-RX-ECT EtherCAT Communi-
cations Unit for MX2/RX-series Inverters: installation,
parameter settings required for operation, trouble-
shooting, and inspection methods.
G5-series AC Servomo-
tors/Servo Drives with
Built-in EtherCAT Com-
munications User’s Man-
ual
I576 R88D-KN@-ECT
R88M-K@
Leaning how to connect
G5-series AC Servomo-
tors/Servo Drives with
Built-in EtherCAT Com-
munications.
Describes the following information for the G5-series
AC Servomotors/Servo Drives with EtherCAT Com-
munications: installation, wiring methods, parameter
settings required for operation, troubleshooting, and
inspection methods.
G5-series Linear
Motors/Drives with Built-
in EtherCAT Communica-
tions Linear Motor Type
User’s Manual
I577 R88D-KN@-ECT-
L
R88L-EC-@W-@
R88L-EC-@M-@
Leaning how to connect
G5-series Linear
Motors/Drives with Built-
in EtherCAT Communi-
cations Linear Motor
Ty pe .
Describes the following information for the G5-series
Linear Motors/Drives with EtherCAT Communica-
tions Linear Motor Type: installation, wiring methods,
parameter settings required for operation, trouble-
shooting, and inspection methods.
Manual name Cat. No. Model numbers Application Description
To Next Page
Loading...
