EasyManua.ls Logo

Omron Powli BU1002SW - User Manual

Omron Powli BU1002SW
94 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
• This manual provides important safety-related information. Thoroughly read and understand
this manual before installing and using the product.
• Keep this manual in a convenient location so that you can refer to it whenever necessary.
BU1002SW/BU3002SW
Uninterruptible Power Supply (UPS/200 to 240V specifi cations)
Instruction Manual
-
バッテリ
 交換
バッテリ
 増設
ブザー停止/テスト
電源出力
バイパス
運転
BU1002SW
-
バッテリ
 交換
バッテリ
 増設
ブザー停止/テスト
電源出力
バイパス
運転

Table of Contents

Questions and Answers

  • C
    Crystal MillerJul 31, 2025
    Why is my Omron UPS switching frequently?
    • A
      Angela DickersonJul 31, 2025
      If your Omron UPS is performing backup too frequently, even when there is no power failure, and you hear switching sounds, it could be due to variations or decreases in the input power, or noise distorting the voltage waveform. Try connecting the UPS to a different wall outlet, ideally one away from equipment that consumes a lot of power. This issue can also occur if many devices are connected to a plug strip or extension cord with a long or thin cable connected to the UPS.
  • R
    randymckeeAug 10, 2025
    What does it mean when the battery replacement lamp blinks on my Omron UPS?
    • J
      Joseph WilliamsAug 10, 2025
      If the battery replacement lamp on your Omron UPS blinks and the beeper sounds at 2-second intervals, it suggests that the auto battery test or self-diagnostic test has determined that the battery is dead. Also, check if the overcurrent protection switch on the rear panel of any connected additional battery unit is turned OFF. If it is OFF, turn it ON, as this can cause a false detection of a deteriorated battery during the auto battery test.
  • M
    Mario LinAug 20, 2025
    How to fix abnormal display on Omron UPS?
    • C
      Carol SmithAug 20, 2025
      If the display on your Omron UPS is abnormal (unstable, showing white lines, or with increased noise), it's likely due to internal noise within the UPS. To address this, ground all devices connected to the UPS by connecting them to a 3-pin wall outlet or connecting their Grounding Terminal to the Grounding Terminal of a wall outlet. This problem may also occur when power cords are long or placed closely, or when the UPS and backed-up devices are placed closely; rearrange them. If the UPS or connected devices are in a metal rack, try grounding the rack itself.

Summary

Safety Precautions

Warning

Highlights high-risk warnings that could cause death or serious injury.

Caution (for installation and connection)

Provides safety warnings specific to installation and connection.

Caution (for use)

Caution (for maintenance)

Caution (for battery replacement)

1-3 Name of each part

Rear view

2 Installation and connection

2-1 Precautions and notes on installation and connection

Essential safety precautions before installing and connecting the UPS.

2-2 Installation and connection

2-3 Connecting the equipment

2-3-2 Connecting a device to the power supply output (BU3002 SW)

2-4 Checking the operation

2-5 Charging the battery

2-6 Measuring the initial value of backup time

3 Operation

3-1 Precautions and notes for operation

Key safety guidelines and important notes for operating the UPS.

3-2 Start and stop procedures and basic operation

Operation after a power failure

Operation during recovery from a power failure

3-3 Interpreting beeps and displays

Displays and beeps when there is an equipment failure

4 UPS functions

4-2 Self-diagnosis test

4-3 Description of the auto battery test function

4-4 Changing the setting of the functions

2. UPS operation mode settings

5 Measuring the backup time

5-1 How to measure backup time

Step-by-step guide to measuring the UPS backup time.

5-2 Estimated backup time

6 Maintenance and Inspection

6-1 Checking the battery

6-2 Replacing the battery

6-3 Replacing the fan

7 Using the UPS monitoring software and contact signal

UPS monitoring software

7-1 When using the included UPS monitoring software to perform auto shutdown

7-2 When performing auto-save functions using the UPS service in Windows Server 2003;XP;2000 + UPS service driver

7-3 When performing auto-save functions using the standard UPS service in Windows Server 2003;XP;2000;NT

7-4 Contact signal

8 Using an SNMP;Web card

8-1 Adding an SNMP;Web card

9 Extending the backup time

9-1 Connecting an additional battery unit

10 Troubleshooting

UPS does not operate.

Troubleshooting steps for when the UPS unit does not power on.

Omron Powli BU1002SW Specifications

General IconGeneral
BrandOmron
ModelPowli BU1002SW
CategoryUPS
LanguageEnglish

Related product manuals