To Next PageTo Next PageWhy doesn’t the RDS work on my Onkyo CR-505DAB Car Receiver?
The current FM station may not support RDS. Try tuning into a station that supports RDS. Also, poor signal strength or too much interference can prevent RDS from working. In this case, change the position or direction of your outdoor FM antenna, and keep it away from fluorescent lights.
What to do if my Onkyo CR-505DAB Car Receiver remote controller doesn’t work?
Try these steps: replace the batteries with new ones, ensuring they are installed correctly. Point the remote directly at the CR-505DAB's remote sensor. Also, make sure that the unit is not exposed to direct sunshine or inverter-type fluorescent lights, which may interfere with the remote sensor. Relocate the unit if necessary.
Why is sound coming from only one speaker on my Onkyo CR-505DAB?
Check the speaker connections of the other speaker and make sure that none of the wires are touching each other, other connectors, or any metal parts.
Why is my Onkyo CR-505DAB Car Receiver reception noisy and intermittent?
This could be due to being too far from the transmitter, the FM antenna being in the wrong position or pointing in the wrong direction, or poor signal strength. Try switching the FM Mode to Mono. You can also adjust the position, height, and direction of your FM antenna.
Why is the FM reception poor on my Onkyo CR-505DAB?
Wave reflections from tall buildings, mountains, or hills might be interfering with the main signal. Try using an FM antenna with better directionality. Alternatively, the station's signal might be too strong; in this case, try an indoor FM antenna.
Why is my Onkyo CR-505DAB reception hindered by a crackling noise?
Crackling noises can be caused by interference from fluorescent lights being turned on or off, or by the ignition systems of passing cars. Try installing an outdoor antenna as far away as possible from nearby roads. Also, move your antenna away from fluorescent lights and adjust the position or direction of your outdoor antenna.
Why does my Onkyo CR-505DAB AM reception have a high-pitched noise?
The high-pitched noise might be caused by interference from your TV. Try moving the AM loop antenna as far away as possible from your TV. You can also move the CR-505DAB as far away as possible from your TV.
Why does my Onkyo CR-505DAB Car Receiver AM reception have a buzzing noise?
The buzzing noise might be caused by interference from electrical equipment, including fluorescent lights. Try relocating your AM antenna.
What to do if my Onkyo Car Receiver doesn’t play a CD?
First, make sure the disc is loaded with the label-side facing up. If the disc is dirty, remove it and clean it. If condensation has formed inside the CR-505DAB, remove the disc and leave the unit turned on for several hours until the condensation has evaporated. Finally, the CD-R/RW disc may be nonstandard.
How to fix Onkyo CR-505DAB Car Receiver CD playback skips?
Skipping can occur due to vibration, so ensure your CR-505DAB is installed in a place free from vibration. Also, the disc may be dirty or scratched. Remove the disc and clean it. If the disc is very scratched, consider buying a new one.
Power Output| power output (DIN) | 20 W + 20 W (4 Ω, 1 kHz) |
|---|---|
| power output (JEITA) | 25 W + 25 W (4 Ω, 1 kHz) |
| dynamic power | 30 W + 30 W (4 Ω) |
Total Harmonic Distortion| THD (AMP) | 0.2% (5 W Output, 4 Ω) |
|---|---|
| THD (FM Stereo) | 0.46% (1 kHz) |
| THD (FM Mono) | 0.4% (1 kHz) |
| THD (AM) | 1.60% |
| THD (DAB) | 0.20% |
| THD (CD) | 0.01% |
Frequency Response| frequency response (AMP) | 10 Hz-50 kHz/+3 dB, –3 dB (LINE) |
|---|---|
| frequency response (FM) | 30 Hz-15 kHz/+1.5 dB, –1.5 dB |
| frequency response (DAB) | 20 Hz-20 kHz |
| frequency response (CD) | 20 Hz-20 kHz |
General Specifications| power supply | AC 230-240 V, 50 Hz |
|---|---|
| power consumption | 75 W |
| stand-by power consumption | 1.0 W |
| dimensions (W x H x D) | 205 W x 103 H x 356 D mm |
| weight | 5.3 kg |
Guide on how to connect speaker wires to the CR-505DAB for audio output.
Instructions for connecting the supplied FM, AM, and DAB antennas.
How to connect external audio sources like tape decks or MD recorders.
Steps to power on the unit and set the internal clock.
Detailed steps for manual clock setting if automatic fails.
Instructions on how to play audio CDs and MP3 discs.
Step-by-step instructions for configuring the timer functions.
A guide to diagnosing and resolving common issues with the CR-505DAB.
Technical details and performance metrics of the CR-505DAB.
