Onkyo HT-R410 User Manual (English)

Other manuals for Onkyo HT-R410

Instruction Manual40 pages

Service Manual61 pages

Questions and Answers:

B
Brian MooreAug 19, 2025
Why is there no sound coming from my Onkyo Receiver?
- A
  Albert PerryAug 19, 2025
  If no sound is coming from your Onkyo Receiver, there could be several reasons: * The muting function might be activated, so deactivate it. * The connections to the AV receiver might not be properly connected, so check them. * The input selector might not be set correctly; set it to the correct input source. * Headphones might be connected; decrease the volume, then disconnect the headphones. * The input signal format might be set to 'PCM' or 'DTS'; set it to 'Auto'.
J
Jacob ArmstrongAug 21, 2025
What to do if my Onkyo Receiver doesn't switch on?
- D
  Dawn LawrenceAug 21, 2025
  If your Onkyo Receiver doesn't switch on: * Check the connection of the power cord. * There may be external noise interfering with the computer circuits of the AV receiver. Disconnect the power cord, then connect it again.
T
Tiffany AshleyAug 23, 2025
What to do if my Onkyo HT-R410 Receiver power shuts off immediately after powering on?
- Q
  qdicksonAug 25, 2025
  If your Onkyo Receiver shuts off immediately after powering on, the amplifier protection circuitry has been activated. Contact your Onkyo Service Center.
S
Shelley DeanAug 26, 2025
Why is there no sound or very little sound from the center speaker on my Onkyo Receiver?
- T
  Travis BruceAug 26, 2025
  If you're getting no sound or very little sound from the center speaker of your Onkyo Receiver, it could be due to a few reasons: * Check the speaker connections to ensure they are properly connected. * Note that no sound is reproduced from the center speaker when the listening mode is 'Stereo' or 'Orchestra'. * Adjust the volume level of the center speaker if it is set to minimum. * Ensure that the selected speaker configuration includes the center speaker.
F
Franklin PriceAug 28, 2025
What to do if the sound of the playback source is not heard on Onkyo Receiver?
- A
  Andrea WrightAug 28, 2025
  If you are not hearing the sound of the playback source on your Onkyo Receiver, make sure the appropriate input source is selected.
K
Kimberly NixonAug 30, 2025
What to do if the Onkyo HT-R410 buttons or remote controller buttons do not operate?
- D
  Daniel JacksonAug 30, 2025
  If the buttons on your Onkyo receiver or remote controller aren't working, it might be due to power supply fluctuations or other abnormalities like static electricity interrupting operation. Disconnect the power cord and then reconnect it.
C
cheryl27Sep 1, 2025
How to fix Onkyo Receiver when no picture appears on the TV screen?
- S
  suzanne40Sep 1, 2025
  If no picture appears on the TV screen when using your Onkyo Receiver, ensure that: * The TV is set to receive the input from the AV receiver. * The video cable is securely connected between the AV receiver and the TV. * If only the S video connection is made, also make a video connection and check both the TV's video input and the AV receiver's output signal.
K
kennethfordSep 3, 2025
Why do the remote controller buttons not operate my Onkyo AV receiver?
- V
  victoria03Sep 3, 2025
  If the buttons on the remote controller do not operate your Onkyo AV receiver, it could be due to several reasons: * Ensure you press the appropriate mode control button. * Insert new batteries if none are present. * Replace worn-out batteries with new ones. * Point the remote controller at the remote sensor of the AV receiver. * Operate the remote controller within 16 feet (5 m) of the AV receiver.
C
Christine WeaverSep 5, 2025
What causes hum or low-frequency noise in Onkyo HT-R410 Receiver?
- R
  Rachel BeltranSep 5, 2025
  Hum or low-frequency noise in your Onkyo Receiver can be caused by incorrect placement of the audio connection cables on the rear panel. Adjust the placement of the cables to reduce the hum.

Onkyo HT-R410 Specifications

Amplifier Section

Power Output Front L/R Speakers	100 Watts per channel min. RMS at 8 ohms 2 channel driven, 20-20, 000 Hz, 0.08% THD
Power Output Center Speaker	100 Watts min. RMS at 8 ohms, 20-20, 000 Hz, 0.08% THD
Power Output Surround L/R Speakers	100 Watts per channel min. RMS at 8 ohms 2 channel driven, 20-20, 000 Hz, 0.08% THD
Dynamic Power Output at 3 ohms	230 watts × 2
Dynamic Power Output at 4 ohms	170 watts × 2
Dynamic Power Output at 8 ohms	115 watts × 2

Input and Output Impedance

Digital Input Optical	0.5 Vp-p, 75 ohms
Digital Input Coaxial	0.5 Vp-p, 75 ohms
Line Input (CD, VIDEO 1, 2, 3, TAPE)	200 mV, 47 kohms
Multichannel Input (DVD FRONT L/C/R, SURR L/R)	200 mV, 47 kohms
Multichannel Input (SUBWOOFER)	36 mV, 47 kohms
Output Level Rec out (TAPE, VIDEO 1)	200 mV, 470 ohms
Output Level Pre out (SUBWOOFER)	1 V, 470 ohms

Tuner Section

FM Tuning Range	87.5-108.0 MHz (100 kHz steps)
FM Usable Sensitivity Mono	11.2 dBf, 1.0 µV (75 ohms, IHF)
FM Usable Sensitivity Stereo	17.2 dBf, 2.0 µV (75 ohms, IHF)
FM 50 dB Quieting Sensitivity Mono	17.2 dBf, 2.0 µV (75 ohms)
FM 50 dB Quieting Sensitivity Stereo	37.2 dBf, 20.0 µV (75 ohms)
FM Capture Ratio	2.0 dB
FM Image Rejection Ratio	40 dB
FM IF Rejection Ratio	90 dB
FM Signal-to-Noise Ratio Mono	76 dB, IHF
FM Signal-to-Noise Ratio Stereo	70 dB, IHF
FM Alternate Channel Attenuation	55 dB, IHF, ±400 kHz
FM Selectivity	50 dB (DIN)
FM AM Suppression Ratio	50 dB
FM Total Harmonic Distortion Mono	0.2%
FM Total Harmonic Distortion Stereo	0.3%
FM Frequency Response	30 Hz-15 kHz, ±1.0 dB
FM Stereo Separation at 1 kHz	45 dB
FM Stereo Separation at 100 Hz-10 kHz	30 dB
AM Tuning Range	530-1, 710 kHz (10 kHz steps)
AM Usable Sensitivity	30 µV
AM Image Rejection Ratio	40 dB
AM IF Rejection Ratio	40 dB
AM Signal-to-Noise Ratio	40 dB
AM Total Harmonic Distortion	0.7%

General Specifications

Power Supply	AC 120 V, 60 Hz
Power Consumption	4.7 A
Dimensions (W × H × D)	17-1/8” × 5-7/8” × 14-3/8”
Dimensions in mm (W × H × D)	435 × 150 × 365 mm
Weight	19.0 lbs., 8.6 kg

View in Manual