Onkyo TX-NR5010 Quick Start Guide

SN 29401234
(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.
* 2 9 4 0 1 2 3 4 *
Quick Start Guide
TX-NR1010
Supplied Accessories
Make sure you have the following accessories:
a
Indoor FM antenna
*1
b
AM loop antenna
*1
c
Speaker cable labels
d
Remote controller and two batteries (AA/R6)
e
Power cord
(Plug type varies from country to country.)
f
Speaker setup microphone
The AV receiver can automatically perform speaker
and surround settings, so that you can easily enjoy a
surround sound tailored to your listening environment.
Connect the supplied microphone to the AV receiver
and follow the on-screen instructions.
When performing automatic speaker setup, connect
your TV to the AV receiver and make the room as
quiet as possible.
*1 (North American models)
Two AM loop antennas and two Indoor FM antennas
are supplied.
a
b
c
d
e
3
2
1
Speaker Cable
f
Using the Remote Controller
Approx. 16 ft. (5 m)
AV receiver
Remote control sensor
Batteries (AA/R6)
Note
Before connecting the power cord, connect all of your speakers and AV components.
1. Connecting Your Speakers
7 84 5
9 10
11 12
1 2 3
6
1
2
Front speakers
3
Center speaker
4
5
Surround speakers
6
Subwoofer(s)
7
8
Surround back speakers
9
10
Front high speakers
11
12
Front wide speakers
Speaker Configuration
5.2-channel:
1
2
3
4
5
6
7.2-channel:
1
2
3
4
5
6
+
7
8
7.2-channel:
1
2
3
4
5
6
+
9
10
7.2-channel:
1
2
3
4
5
6
+
11
12
9.2-channel
*2
:
1
2
3
4
5
6
+
7
8
+
9
10
9.2-channel
*2
:
1
2
3
4
5
6
+
7
8
+
11
12
9.2-channel
*2
:
1
2
3
4
5
6
+
9
10
+
11
12
*2 By adding an external amplifier to the 7.2-channel configuration,
you can enjoy 9.2-channel playback. For details, please refer to
the instruction manual.
Please connect
1
,
2
,
3
,
4
,
5
and
6
for 5.1-channel surround.
1/2''-5/8'' (12-15mm)
*3
Powered
subwoofer
6
Surround
speaker R
5
Surround
speaker L
4
2
Front
speaker R
3
Center speaker
1
Front
speaker L
Surround back
speaker R
8
Surround back
speaker L
7
10
Front high
speaker R
12
Front wide
speaker R
11
Front wide
speaker L
9
Front high
speaker L
*3 The level and distance can be set individually for each output. If you’re using only one subwoofer, connect it to
SW1 PRE OUT.
E n
- 2 -
Red Green White
BlueGray Tan Brown
RedRed White White
The number of
terminals/jacks and
their shapes vary
from country to
country.

Onkyo TX-NR5010 Specifications

General

Output level	0.001 mV
Receiver type	Surround
Frequency range	5 - 100000 Hz
Output impedance	470 Ω
Input sensitivity	200 mV
Audio output channels	9.2 channels
Signal-to-Noise Ratio (SNR)	110 dB
Total Harmonic Distortion (THD)	0.05 %
Dynamic power per channel (3 Ohm)	400 W
Dynamic power per channel (4 Ohm)	300 W
Power output per channel (1KHz@6 Ohm)	220 W
Power output per channel (20-20KHz@8 Ohm)	180 W
HDMI in	9
PC in (D-Sub)	Yes
Audio (L/R) in	7
Composite video in	5
Digital audio coaxial in	3
Digital audio optical in	4
Component video (YPbPr/YCbCr) in	2
Component video (YPbPr/YCbCr) out	1
Speakers connectivity type	-
Audio formats supported	AAC, FLAC, LPCM, MP3, OGG, WAV, WMA
Ethernet LAN	No
AM band range	522 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Preset stations quantity	40
Product color	Black
Audio decoders	Dolby Pro Logic IIz, Dolby TrueHD, DTS Neo:X, DTS-HD
Apple docking compatibility	Not supported
AC input voltage	220-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.15 W
Power consumption (typical)	1160 W
Package weight	29000 g
Cables included	AC

Weight and Dimensions

Depth	463.5 mm
Width	435 mm
Height	198.5 mm
Weight	25000 g