1
Introduction
Before using the product
Only qualied personnel of electrical and mechanical engineering should
work with the product. Use the product correctly after thoroughly reading the
"Safety precautions." In addition, be sure to observe the contents described in
warning, caution, and note in this manual.
The product described in this manual has been designed and manufactured
for use in general industrial machinery, and must not be used for any other
purpose. For the power supply, use a DC power supply with reinforced
insulation on its primary and secondary sides. Oriental Motor Co., Ltd. is not
responsible for any damage caused through failure to observe this warning.
Operating manuals for the BLV Series
Operating manuals for the
BLV
Series are listed below. Read the manuals
carefully before using your
BLV
Series unit.
BLV
Series OPERATING MANUAL (This document)
This manual explains the motor and driver functions as well as installation
method, and others.
BLV
Series USER MANUAL Basic Function
This manual explains the motor and driver functions, installation and
connection methods, operations using the support software
MEXE02
or data
setter
OPX-2A
, as well as troubleshooting and others.
BLV
Series USER MANUAL RS-485 Communication Mode
This manual explains how to control the motor via RS-485 communication.
The USER MANUAL (Basic Function, RS-485 Communication Mode) does
not come the product. For details, contact your nearest Oriental Motor sales
oce or download from Oriental Motor Website Download Page.
CE Marking
This product has been certied under the CE Marking requirements (EMC
Directive) based on the EN Standard. Because the input power supply voltage
of this product is 24 VDC/48 VDC, it is not subject to the Low Voltage
Directive. However, install and connect this product as follows.
Installation conditions
Motor and driver are to be used as a component within other equipment.
Overvoltage category: I Pollution degree: 2
EMC Directive
Refer to USER MANUAL Basic Function for installation method.
Republic of Korea, Radio Waves Act.
KC Mark is axed to this product under the Radio Waves Act, the republic
of Korea.
RoHS Directive
The products do not contain the substances exceeding the restriction values of
RoHS Directive (2011/65/EU).
Safety precautions
The precautions described below are intended to prevent danger or injury to
the user and other personnel through safe, correct use of the product. Use the
product only after carefully reading and fully understanding these instructions.
Handling the product without observing the
instructions that accompany a "WARNING"
symbol may result in serious injury or death.
Handling the product without observing the
instructions that accompany a "CAUTION"
symbol may result in injury or property damage.
The items under this heading contain important
handling instructions that the user should observe
to ensure safe use of the product.
Do not use the product in explosive or corrosive environments, in the
presence of ammable gases, locations subjected to splashing water, or
near combustibles. Doing so may cause re, electric shock or injury.
Only qualied and educated personnel should be allowed to perform
installation, connection, operation and inspection/troubleshooting of the
product. Handling by unqualied personnel may result in re, electric
shock, injury or damage to equipment.
Do not transport, install the product, perform connections or inspections
when the power is on. Always turn the power o before carrying out these
operations. Doing so may result in electric shock or damage to equipment.
Do not use a standard type product in vertical drive such as elevating
equipment. If the driver’s protection function is activated, the motor will stop
and the moving part may drop, thereby causing injury or equipment damage.
Do not use the brake mechanism of the motor with electromagnetic brake as
a safety brake. It is intended to hold the movable parts and motor position.
This caution is to avoid personal injury or damage to the equipment.
When the driver's protection function is triggered, rst remove the cause
and then clear the protection function. Continuing the operation without
removing the cause of the problem may cause malfunction of the motor and
driver, leading to injury or damage to equipment.
Install the motor, gearhead and driver in an enclosure. Failure to do so may
result in electric shock or injury.
Keep the driver's input-power voltage within the specied range to avoid re
or electric shock.
For the power supply, use a DC power supply with reinforced insulation on
its primary and secondary sides. Failure to do so may cause electric shock.
Securely connect the cables in accordance with the connection examples.
Failure to do so may result in re or electric shock.
Do not forcibly bend, pull or pinch the cable. Doing so may result in re,
electric shock or damage to equipment.
Do not machine or modify the motor cable or connection cable. Doing so
may result in re, electric shock or damage to equipment.
Be sure to observe the specied cable sizes. Use of unspecied cable sizes
may result in re or electric shock.
Observe the specied screw tightening torque when connecting terminals to
the connector. Failure to do so may result in re or equipment damage.
Use a motor, gearhead, and driver only in the specied combination. Failure
to do so may result in re, electric shock or damage to equipment.
When the electromagnetic brake motor is used in an application of vertical
drive such as elevating equipment, operate it after checking the condition of
a load suciently so that a load in excess of the rated torque is not applied
or a small value is not set in the torque limiting value. Failure to do so may
result in injury or damage to equipment.
Always turn o the power before performing maintenance/inspection.
Failure to do so may result in injury.
Do not touch the motor or driver when conducting the insulation resistance
measurement or dielectric strength test. Accidental contact may result in
electric shock.
Regularly check the openings in the driver for accumulated dust.
Accumulated dust may cause re.
Do not disassemble or modify the motor, gearhead and driver. Doing so may
result in injury or damage to equipment. Refer all such internal inspections and
repairs to the branch or sales oce from which you purchased the product.
Do not use the motor, gearhead and driver beyond the specications. Doing
so may result in electric shock, injury or damage to equipment.
Keep your ngers and objects out of the openings in the driver, or re,
electric shock or injury may result.
Do not touch the motor, gearhead or driver while operating or immediately
after stopping. The surface of the motor, gearhead or driver may be hot and
cause a skin burn(s).
HM-5112-6
OPERATING MANUAL
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and
safety precautions.
Please read it thoroughly to ensure safe operation.
Always keep the manual where it is readily available.
Brushless Motor and Driver Package
BLV Series
To Next Page
Need help?
General
