EasyManua.ls Logo

Oriental motor BLVM620K-GFS - User Manual

Oriental motor BLVM620K-GFS
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HM-5113-9
Brushless Motor and Driver Package
BLV
Series
Standard Type, Electromagnetic Brake Type
USER MANUAL (Basic Function)
Thank you for purchasing an Oriental Motor product.
This Manual describes product handling procedures and safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.

Table of Contents

Other manuals for Oriental motor BLVM620K-GFS

Preview: Operating Manual
Operating Manual8 pages

Questions and Answers

  • A
    allenchaseAug 9, 2025
    Why is my Oriental motor Engine not rotating?
    • B
      Beth Wilson DDSAug 9, 2025
      If your Oriental motor Engine isn't rotating, first ensure the driver and power supply are properly connected. If both the FWD and REV inputs are ON or OFF, turn either FWD or REV input ON. If the internal potentiometer is not adjusted, turn it clockwise to set the speed. Ensure the potentiometer is correctly selected: turn the M0 input OFF for the internal potentiometer, or ON for the external one. Check the external potentiometer or DC voltage connection. Finally, if the ALARM LED is blinking, it indicates a protective function has been triggered; refer to p.64 to reset the alarm.
  • N
    Nathan BurtonAug 14, 2025
    What to do if my Oriental motor Engine rotates in the opposite direction?
    • T
      Thomas BlackburnAug 14, 2025
      If your Oriental motor Engine rotates in the wrong direction, check the FWD and REV input connections. The motor should rotate clockwise when FWD is ON and counterclockwise when REV is ON. If you're using a gear ratio where the gearhead output shaft rotates opposite to the motor, or a combination type-hollow shaft flat gearhead, reverse the FWD and REV input operations. With the combination type-hollow shaft flat gearhead, ensure you are viewing the gearhead in the correct direction as the rotation direction changes based on the viewing direction.
  • S
    Susan PalmerAug 21, 2025
    Why does my Oriental motor BLVM620K-GFS Engine not stop instantaneously?
    • J
      Jody PatrickAug 21, 2025
      If your Oriental motor Engine doesn't stop immediately, ensure the STOP-MODE input is OFF to enable instantaneous stopping. Also, consider whether the load inertia is too large; if so, reduce it.
  • M
    Michael AlvaradoAug 27, 2025
    How to fix unstable operation and excessive vibration in my Oriental motor BLVM620K-GFS Engine?
    • D
      Dustin RodriguezAug 27, 2025
      If your Oriental motor Engine operation is unstable or the motor vibration is excessive, first check the alignment of the motor and gearhead output shaft with the load shaft. Misalignment can cause instability. Also, consider the effect of electrical noise. To check for noise, operate only the essential equipment (motor, driver, and required external equipment). If noise is present, keep away from noise sources, reconsider the wiring, use shielded cables, and install ferrite cores.
  • J
    jerrymoralesSep 1, 2025
    What to do if the electromagnetic brake of my Oriental motor Engine does not hold the load?
    • P
      Patrick FritzSep 2, 2025
      If the electromagnetic brake on your Oriental motor Engine isn't holding the load, ensure the MB-FREE input is turned OFF. When MB-FREE is ON, the brake is disengaged.

Summary

Safety Precautions

General Safety Warnings and Cautions

Critical warnings and cautions for safe handling, covering potential serious injury or damage from pages 4 and 5.

System Configuration

Preparation

Product Check and Model Combinations

Installation

Installation Location Guidelines

Motor and Parallel Shaft Gearhead Installation

Hollow Shaft Gearhead Installation Details

Round Shaft Motor Installation and Mounting

Load Installation Techniques

Permissible Radial and Axial Loads

Driver Installation and Mounting

EMC Directive Compliance: Cable Wiring

Guides on wiring power and signal cables for EMC Directive compliance.

EMC Wiring, Grounding, and Static Electricity Precautions

Connection

Connection Guidelines by Model

Power Supply Connection Procedures

Explains the method for connecting the DC power supply and notes for power ON/OFF.

Motor and Driver Connection Procedures

Details how to connect the motor and driver, including electromagnetic brake connectors.

I;O Signal Connection and Circuit Diagrams

Input Signal Function Descriptions

Output Signal Function Descriptions

Example Connection Diagrams for Logic

Operation

Operation Overview and Types

Basic Speed Setting Methods

Details setting motor speed via internal/external potentiometers or external DC voltage.

Motor Operation and Stop Control

Explains how to start and stop the motor using input signals and stop modes.

Acceleration and Deceleration Time Setting

Guides on setting acceleration and deceleration times for motor start/stop.

Motor Rotation Direction Control

Explains how to set and control the motor output shaft rotation direction.

Speed Response and Two-Speed Operation

Operation Patterns and Torque Limiting Function

Sink and Source Logic Selection

Explains how to select sink or source logic for input/output signal connections.

Extended Function

Extended Functionality Overview

How to Use MEXE02

Starting MEXE02 Software

Guides on launching MEXE02, setting communication ports, and selecting the product.

Setting Operation Data in MEXE02

Explains how to enter and select operation data within the MEXE02 software.

MEXE02 Parameter Setting and Data Writing

Guides on editing and writing parameters using the MEXE02 software.

MEXE02 Status Monitor Functionality

MEXE02 Alarm and Warning Monitoring

MEXE02 Teaching;Remote Operation

Guides on performing teaching and remote operation of the motor using MEXE02.

MEXE02 I;O Test Functionality

Explains how to perform an I/O test to verify signal connections and data conversion.

Setting Contents of MEXE02

MEXE02 Data Update Timing

MEXE02 Parameter List: Operation & Function

Lists parameters for operation data and function settings.

MEXE02 Parameter List: I;O, Alarm, Operation, Comms

Lists parameters for I/O selection, alarm/warning, operation, and communication settings.

MEXE02 Function Setting Details

MEXE02 I;O Function Selection Guide

Guides on selecting functions for input and remote I/O signals.

MEXE02 Input;Output Signal Function Lists

MEXE02 Alarm, Warning, Test Operation Settings

MEXE02 Operation Settings and Input Modes

Details operation settings, analog input selection, and 2-wire/3-wire input modes.

MEXE02 Communication Parameter Settings

Details communication settings such as timeout, error alarm, parity, and stop bits.

Protective Functions

Alarm Codes and Remedial Actions

Lists alarm types, causes, and remedial actions based on ALARM LED blink patterns.

Additional Alarm Codes and Remedial Actions

Troubleshooting and Remedial Actions

Motor Operation Troubleshooting Guide

Specifications

Model-Specific and General Specifications

Connector and Cable Pin Assignments

Peripheral Equipment (Sold Separately)

Oriental motor BLVM620K-GFS Specifications

General IconGeneral
Motor TypeBrushless DC Motor
Frame Size60 mm
Rated Output Power200 W
Output Power200 W
Shaft Diameter12 mm
Speed Range30~3000 rpm
Torque0.637 Nm

Related product manuals