Oriental motor BLVM620K-GFS - Specifications; Model-Specific and General Specifications

Specications
−67−
15 Specications
15.1 Specications
The value in a state where the gearhead is not combined is described in each specication for the rated torque, the
maximum instantaneous torque, the rated rotation speed, and the speed control range.
•
The box (

) in the model name indicates a number representing the gear ratio.
•
The box (

) in the model name indicates a number representing the length of an connection cable.
Model
Combination type-parallel
shaft gearhead
BLV510K

S-

BLV510KM

S-

BLV620K

S-

BLV620KM

S-

BLV640N

S-

BLV640NM

S-

Combination type-hollow
shaft at gearhead
BLV510K

F-

BLV510KM

F-

BLV620K

F-

BLV620KM

F-

BLV640N

F-

BLV640NM

F-

Round shaft type −
BLV620KA-

BLV620KMA-

BLV640NA-

BLV640NMA-

Rated output power (Continuous) 100 W 200 W 400 W
Power
supply input
Rated voltage 24 VDC 24 VDC 48 VDC
Permissible voltage range ±10%
Rated input current
*1
6.3 A (6.5 A) 13 A 11 A
Maximum input current
*1
10 A (11 A) 25 A 18 A
Rated torque 0.319 N·m (45 oz-in) 0.65 N·m (92 oz-in) 1.3 N·m (184 oz-in)
Peak torque
*2
0.638 N·m (90 oz-in) 1.15 N·m(163 oz-in) 1.8 N·m (250 oz-in)
Rated rotation speed 3000 r/min
Speed control range
100 to 3000 r/min
(analog setting)
80 to 3000 r/min
(digital setting)
*3
100 to 4000 r/min (analog setting)
80 to 4000 r/min (digital setting)
*3
*1∗
( ): For electromagnetic brake type
*2∗
The peak torque can be used for about ve seconds maximum.
*3∗
The specication is applied when setting with the
OPX-2A
,
MEXE02
, or communication.
15.2 General specications
Motor Driver
Operating
environment
Ambient
temperature
0 to +40 °C [+32 to +104 °F] (non-freezing)
Ambient
humidity
85% or less (non-condensing)
Altitude 1000 m (3300 ft.) or lower above sea level
Surrounding
atmosphere
No corrosive gas or dust. Cannot be used in radioactive materials, magnetic eld, vacuum or
other special environment. (For details about installation locations, refer to p.12.)
Vibration
Not subject to continuous vibrations or excessive impact. In conformance with JIS C 60068-2-6
"Sine-wave vibration test method"
Frequency range: 10 to 55 Hz Pulsating amplitude: 0.15 mm (0.006 in.)
Sweep direction: 3 directions (X, Y, Z) Number of sweeps: 20 times
Storage
environment
Shipping
environment
Ambient
temperature
−25 to +70 °C [−13 to +158 °F] (non-freezing)
*
−25 to +70 °C [−13 to +158 °F] (non-freezing)
Ambient
humidity
85% or less (non-condensing)
Altitude 3000 m (10000 ft.) or lower above sea level
Surrounding
atmosphere
No corrosive gas, dust, water or oil.
Cannot be used in radioactive materials, magnetic eld, vacuum or other special environment.
Degree of protection
BLV510
: IP65 (except for the connector part)
BLV620
,
BLV640
: IP40
IP20
∗*
For
BLV510KM
: −20 to +70 °C [−4 to +158 °F] (non-freezing)