Pacific SC8230S - User Manual

Questions and Answers

A
Amy SavageSep 6, 2025
What to do if the motor stops running in my Pacific SC8230S Ventilation Hood?
- S
  Steven AndersonSep 7, 2025
  If the motor in your Pacific Ventilation Hood stops running, there could be several causes. It could be due to a burned wire or fuse, in which case you should replace the PC board. Alternatively, the motor temperature regulator might be off and unrecoverable, or the motor copper wire could be burned; in either of these situations, the motor should be replaced. Another possibility is a defected capacitor, which would require replacing the capacitor. Finally, check the power meter for no power or a burned fuse; if found, replace the power cord.
S
spalmerAug 22, 2025
Why does my Pacific SC8230S motor stop running?
- C
  cbeardAug 22, 2025
  The motor may stop running due to several reasons: a burned wire or fuse (in which case, replace the PC board or check the power meter and replace the power cord if necessary), a motor temperature regulator that is off and can’t be recovered, burned motor copper wire, or a defected capacitor. For the latter two, the suggested solution is to replace the motor or the capacitor, respectively.
A
alisonthompsonSep 4, 2025
What to do if the display unit failed on my Pacific SC8230S Ventilation Hood?
- E
  ehoffmanSep 4, 2025
  If the display unit has failed, the cause could be a failed main control PC board, a failed PC board switch, a clogged nozzle, or a failed water pump. Consider replacing the main control PC board, the PC board switch, checking the nozzle, or changing the water pump.
K
Kevin BooneSep 2, 2025
What to do if two sections of the Halogen light are not working on my Pacific SC8230S Ventilation Hood?
- N
  Nicholas WeberSep 2, 2025
  If two sections of the Halogen light are not working, the cause may be a short circuit on the Halogen light control power cord, a short circuit on the light power cord in the main control PC board, or the Halogen light may have failed. Try replacing the Halogen light control power cord, the main control PC board, or the Halogen light.
S
Sean WarrenSep 1, 2025
Why are the fan blades inverted on my Pacific Ventilation Hood?
- M
  Michael MillerSep 1, 2025
  Inverted fan blades can be caused by a short circuit on the motor, or if air comes out of the air outlet instead of being sucked up because the air outlet or exhaust pipe is blocked. Replace the motor or clean the blocked air outlet or exhaust pipe.
B
Bruce RobinsonAug 30, 2025
What to do if two sections of the LED light are not working on my Pacific SC8230S?
- J
  jonesamyAug 30, 2025
  If two sections of the LED light are not working, it could be due to a short circuit on the LED light control power cord, a short circuit on the light power cord in the main control PC board, or a failed LED light. Replace the LED light control power cord, the main control PC board, or the LED light, respectively.
C
Christine WardAug 29, 2025
Why does my Pacific SC8230S have power leakage?
- C
  Cassandra NormanAug 29, 2025
  Power leakage could be caused by water getting into the motor. In this case, replace the motor.
T
Timothy RussellAug 27, 2025
What to do if the delay-off function fails in my Pacific Ventilation Hood?
- J
  John MurrayAug 28, 2025
  If the delay-off function fails, the main control PC board or the PC board switch may have failed. Replacing the main control PC board or the PC board switch should solve the problem.
J
Jillian BoydAug 27, 2025
What to do if my Pacific SC8230S motor doesn’t regulate speed?
- R
  robert89Aug 27, 2025
  If the motor isn’t regulating speed, it could be due to a defected capacitor or the electrical wiring being off. Try replacing the capacitor or fixing the electrical wires.
L
Leonard GardnerAug 25, 2025
Why is my Pacific Ventilation Hood motor running on and off?
- P
  patricia92Aug 26, 2025
  The motor might be running on and off because it reaches an unusually high temperature during cooking and stops, then restarts when it cools down. It may also be caused by motor temperature regulator coming on and off. Consider changing your cooking routine slightly or change the motor electrical wiring and de-activate the temperature regulator.