50
Troubleshooting(continued)
CQ-DVR592U
E
N
G
L
I
S
H
35
51
E
N
G
L
I
S
H
36
CQ-DVR592U
A mobile phone is used near the unit.
➡ Keep the mobile phone away from the unit.
Noise.
❐ Common (continued)
❐ Radio
Too much noise in FM
stereo and monaural
broadcasts.
Station is too far, or signals are too weak.
➡ Select other stations of higher signal level.
The radio antenna is not extended enough.
➡ Extend fully the radio antenna.
Battery cable is not correctly connected.
➡ Connect the battery cable to the terminal that is always active.
Preset station is reset.
Trouble Cause/Step
The motor antenna relay control lead is not connected correctly.
➡ If there is a motor antenna in the car, connect the motor antenna
relay control lead to the motor antenna lead that is installed in the
car correctly.
The disc is inside but no
sound.
Disc is upside down.
➡ Place disc in the correct direction with the label side up.
❐ DVD/Video CD/CD
Disc is dirty, or has scratches.
➡ Clean disc or change disc, referring to the section on “Notes on Disc”.
Trouble Cause/Step
The unit can only play the following types of discs: DVD video, Video
CD, CD and CD-DA data recorded CD-R and CD-RW, and MP3 data
recorded CD media (CD-ROM, CD-R, CD-RW).
➡ The unit may not successfully play back a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive)
and a disc which are incompatible one another. Refer to
instructions for the concerned devices for details.
❐ DVD/Video CD/CD (continued)
≥ Disc is defective.
≥ Mechanical trouble.
➡ Open the panel and press [<] (eject). If the disc still does not eject,
press the reset switch. (➡ page 54)
Disc is not ejected.
Disc is dirty, or has scratches.
➡ Clean disc, referring to the section on “Notes on Disc
”
.
CD text is not displayed
normally.
The first track of a mix mode disc was reproduced. (Mix mode is a
format in which data except music is recorded on the first track and
music data is recorded on other than the first track in a session. )
➡ Play back music data recorded on other than the first track.
Time is counted but no
sound comes out.
The disc will not play, or
else it stops very
quickly.
Mounting angle is over 30x.
➡ Adjust mounting angle to less than 30x.
Unstable mounting.
➡ Mount the unit securely with the mounting parts, referring to the
section on installation.
Sound skips due to
vibration.
≥ Condensation (dew).
➡ Wait for a while before use.
≥ Disc is dirty, or has scratches.
➡ Clean disc or change disc, referring to the section on “Notes on Disc”.
The picture does not
appear on the monitor.
Cables are not correctly connected.
➡ Connect cables correctly.
➡ Check the settings for the monitor itself.
➡ Stop the car and apply the parking brake.
Video CD menu playback
does not work.
➡ Menu playback is only possible when playing a video CD that has
the playback control feature.
The buttons do not work.
Some operations are not permitted with certain discs.
➡ Refer to the guide provided with your disc.
➡ The unit may not successfully play back a CD-R/RW that was made
by the combination of writing software, a CD recorder (CD-R/RW
drive) and a disc if they are incompatible one another. Refer to
instructions for the concerned devices for details.
Disc is dirty, or has scratches.
➡ Clean disc or change disc, referring to the section on “Notes on Disc”.
Sound skips, bad sound
quality. (e. g. caused by
noise)
Trouble Cause/Step Trouble Cause/Step
You are trying to play a dts CD or DVD.
➡
The player cannot play audio on dts CDs or DVDs unless a digital surround
processor is used
(➡ pages 72–73)
.
To Next Page
Loading...
