To
select these options, perform steps
0-0
(~
30)
"Network"
IP
AddresslDNS Settings
(q
17)
e Press [OK] to show the following settings.
Connection Test
----
IP
Address
Auto Configuration (DHCP)
eQn
eOff
IP
Address
---.---.---.---
Subnet Mask
---.---.---.---
Default Gateway
---,---.---.---
DNS
Auto
Configuration (DHCP)
eQn
eOff
Primary DNS
---.---.---.---
Secondary
DNS
- -
-.
- -
-.
- -
-.
-
--
Auto Detect Connection Speed
eQn
eOff
Connection Speed Setting
e10BASE Half Duplex e10BASE Full Duplex
This is enabled only when "Auto Detect Connection Speed" is
e 100BASE Half Duplex e100BASE Full Duplex
turned "Off".
Proxy Server Settings
(q
18)
e Press [OK)
to
show the following settings.
Reset
to
factory
preset
eYes
e.t:iQ
Proxy Address
(The initial setting
is
blank.)
Proxy Port Number
(The initial setting is "0".)
"Others"
Off Timer
e2
Hours
e~
eOff
Select how long the unit remains on when it
is
not being
used.
Remote Control Code
eSet
Code 1
eSet
Code 2 eSet Code 3
Easy Setting
eYes
e.!'4.Q
You
can execute basic settings ("On-screen Language", ''TV
Aspect", "Analog Audio Output"
~.
Restore Default Settings
eYes
eliQ
This returns all values
in
the Setup menu and the on-screen
menu, except for "Remote Control Code", "On-screen
Language", "IP Address/DNS Settings", "Proxy Server
Settings". "DVD-Video Ratings" and "BD-Video Ratings" to
the default seHings.
DlvX Registration
Em3
(q
24)
You
need this registration code to purchase and play DivX Video-on-Demand (VOD) content.
Firmware Update
(q
14)
e Press [OK) to show the following settings.
Automatic
Update Check
eQn
eOff
When this equipment remains connected to the Internet,
it will check for the latest firmware version when it is
turned on and you can update it if necessary.
Update Now
You
can update the firmware manually.
The unit's remote control code
Press and hold [OK) and the
indicated number button at the
same time for more than 5 seconds.
PrIlI'SI~Jl3m110XJ
togethcr
lio'manJIlL:I.n55NOftlJson
!be"""""'.
Remote Contror COde
~
-
-
I
I
I
:33~
.....
.
._._
...
_.
..
_
._
...
__
....
...
__
._
....
_
...
_
....
..
..
_
...
_~_-:;J
RQT9243
o Press [SETUP].
e Press [A,
T]
to
select
"Others"
and press [OK].
e Press
[A,
T]
to
select
"Remote
Control
Code"
and press [OK].
o Press
[A,
T]
to
select
the
code (1,2,
or
3) and
press
[OK].
oTo change
the
code on the remote control
While
pressing
[OK], press and
hold
the
numbered
button
([1], [2]
or
[3])
for
more
than 5 seconds.
o Press [OK].
When
other
Panasonic products respond
to
this
remote control
Change the remote control code
on
the main unit and the remote control (the two must match) if you place other Panasonic products close together.
When the following indicator
appears on the unit's display and
you are unable
to
operate
the
unit
To Next Page
Loading...
