Changing the unit's settings
Changing the speaker setting to suit your speakers
B055
- . . - -
When connecting to
an
amplifier/receiver to enjoy multi-channel surround sound. use the following settings on this unit if they cannot be set on the
amplifier/receiver.
The
settings
are
effective
when
connecting
to
analog
7.1
ch/5.1ch AUDIO
OUT
terminal.
Preparation
o Set "Analog Audio Output" to "2ch (Downmix) +
5.1
ch" or '7.1ch".
(~
32)
A message is displayed.
e Press [OK].
Center
Front
(L)
Com
plete
---,--==~
Test
---,'---~-'
Front
(R)
Subwoofer
Delay
time
(
Ii]
)
For optimum listening with 7.1/5.1-channel sound. all the speakers.
except for the subwoofer. should be the same distance from the
seating position.
If you have to place the center, surround and surround back speakers
closer to the seating position, adjust the delay time to make up for the
difference.
If either distance
@ or © is less than ®
(~
below), find the
difference
in
the relevant table and change to the recommended
setting.
o Press [
••
~,
....
~)
to select the delay time box
(Ii])
and press
[OK].
e Press
[.,
~)
to select the setting and press [OK).
5.1ch
speaker
connection
7.1ch
speaker
connection
• Surround back channel
is
enabled only when setting "Analog Audio
Output" to
"7.1
ch".
Speaker presence and size (
~~~~~~(;J
)
Set all the connected speakers individually.
o Press
[.,
~,
....
~)
to select the speaker icon and press [OK).
e Press
[.,
~)
to select the setting and press [OK].
Icon
examples:
Surround speaker (LS)
Actual speaker position
Ideal speaker position
Approxim.~!~
room dimensions
Difference
Selting
Approx. 34 cm
(1
ft.
1 in.)
1.0 ms
Approx. 68 cm (2
ft.
2 in.)
2.0 ms
Approx. 102
cm
(3
ft.
4 in.)
3.0ms
Approx. 136
em
(4
ft.
5 in.) 4.0 ms
Approx. 170 cm (5 ft. 6 in.) 5.0 ms
Difference
Setting
Approx. 170 cm (5
ft.
6 in.)
5.0ms
Approx. 340
cm
(11
ft.
1 in.) 10.0 ms
Approx. 510
em
(16
ft.
8 in.) 15.0 ms
® ® © :Primary listening distance
@
Center
speaker
©
Surround/Surround
back
speakers
(LB)
Surround
back
(RB)'
D
(LS)
Surround
(RS)
~
dEl
,me
dB
:a,
'~
l!I!I'DlliIiIl~.~.J
Large
-Large:
-Small:
~
Small
No
Select when the speaker supports low-frequency
(under 100 Hz) reproduction.
Select when the speaker does not support
low-frequency reproduction.
In
order to make
an
ideal listening environment, settings of speaker
sizes may
be
automatically adjusted.
For example, if the subwoofer
is
set to "No", the front speakers will
automatically be set to "Large". (In this case, we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
Channel balance
(~)
o Select "Test" and press [OK].
A test signal
is
output.
Front
(L)~Center~Front
(R)----->
Surround (RS)
t !
Surround (LS)
+--
Surround Back (LB)
+--
Surround Back (RB)
e While listening to the test signal. press
r.,
~)
to adjust the
volume of each speaker
Front speakers: 0.0 to
-6.0
dB
Center and surround speakers: 0.0 to
-12.0
dB
-
You
cannot adjust the volume of surround back speakers.
€)
Press [OK].
The test signal stops.
- No signal is output for the subwoofer.
To
adjust its volume. play
something. then return to this screen to adjust to suit your taste.
o Press [OK].
RQT9243
To Next Page
Loading...
