Changing the unit's settings
"Display"
(continued)
.
(-"
To
select
these
options,
perform
steps
0-0
(Q
32)
I
Underlined
items
are
the
factory
presets.
!
FL Oisplay
e Bright
Changes
the brightness
of
the unit's display.
eOim:
The display is dimmed.
eAuto:
The display is
dimmed
during playback and bright
except playback.
SO
Card
LEO
Control
fs'Ciiio
1
eOn
eOff
Set the lighting
method
forthe'lamp
on the SO card slot.
eSO
inserted:
When this unit is turned
on
and SO card is inserted, the
lamp is lighted.
License
Information about the software used by this unit is displayed.
"TV
I Device
Connection"
In
thiS
unit, a P4HO
(q
51) Video
processor
IS
used to proVide Video
of
optimal resolution to the connected TV.
TV
Aspect
When connected to a 4:3 aspect television:
Set
to match the type
of
television connected.
e4:3
Pan & Scan: Video recorded for a widescreen is played as Pan & Scan
(unless prohibited
by
the
producer
of
the disc). When playing
BO-Video, video is
output
as "4:3 Lellerbox".
-4:3
Lellerbox:
Video recorded for a widescreen is piayed
in
the
ietterbox
style.
When
connected to a 16:9 widescreen television:
-16:9:
Video recorded for 4:3 aspect screen is displayed as a 4:3 ratio
image in the center
of
the screen.
e16:9
Full: Video recorded for 4:3 aspect screen is displayed as a
horizontally stretched 16:9 image.
HOMI
Connection
ePress
[OK] to
show
the following settings.
HOMI Video Mode
eOn:
Images are output from
the
HOM
I terminal
in
the resolution set
in
"HDMI
Select "On"
when
video is output from HOMI AV
OUT
Resolution". Video from COMPONENT VIDEO OUT terminal
is
output
as
"480i".
terminal.
eOff
Images
are output in the resolution set in
"Component
Video Resolution".
HOMI Resolution*
-Auto:
Automatically selects the
output
resolution best suited to the
The items supported by the connected devices are connected television (1080p, 1080i,
nop
or
480p).
indicated on the screen as
"*".
When
any
item without
e480p
enop
"*"
is selected, the images
may
be distorted.
-1080i
e1080p
-
When
outputting 1080p signal, we
recommend
using High Speed HOMI Cables
that
have the
HOMIIogo
(as shown on the cover) and are less than 5.0 meters to
prevent video distortion etc.
-When
the unit is connected to an amplifier/receiver that does not support the
resolution set on the unit, the video
cannot
be
output
properly. In this case, use
the HOMI cable to
connect
the unit to the
TV
and then connect the unit to the
amplifier/receiver using a cable
other
than HOMI.
-
To
enjoy high definition video up-converted
to
1080p, you
need
to
connect
the
unit
directly
to 1080p compatible
HOTV
(High Definition Television). If this unit
is
connected
to
an
HDTV through other equipment, it must also
be
1080p compatible.
24p
Output
I:mI.'J
~
-On:
Images
in
24p are output
in
24p as they are.
When
this unit
is
connected
to
a
TV
supporting 1080/24p output
However,
via
an
HDMI
cable, this unit displays each
frame
at
1/24
second
-when
video is being output at 24 frames, images from
any
other terminal
intervals - the same interval originally shot
with
the film camera.
than the HOMI terminal
may
not be
output
properly.
e When playing OVO-Video, set to "On" and then set "24p"
-ImI!I:
when images other than 24p are played, images are output
at
60p.
in
"Video"
(q
31) to "On"
-Off
HOMI RGB
Output
Range
eStandard: The video is output as it is.
Effective when connected to a device that only supports
eEnhanced:
When the black and white
contrast
of
a video is low, the signal
RGB output.
is enhanced to reproduce
clear
video.
HOMI
Audio
Output
-On:
This setting selects
whether
or not to output audio from
-Off:
When
the
TV
is connected to this unit
using
an HOMI cable, and this unit
HOMI.
is also connected to other devices, such
as
an amplifier/receiver using an
optical digital audio cable
or
a coaxial cable I
B080
I.
VIERA
Link
eOn:
Set to use "HOAVI Control" function
when
connected with
-Off:
Select when you
do
not
want
to use "HOAVI Control".
an HOMI cable to a device that supports "HOAVI Control".
Component
Video Resolution*
-480i
e480p
enop
e1080i
This sets the video output resolution
when
using the
Even
if
you
select
"nOp"
or "1080i",
the
video output resolution is restricted
to
"480p"
when
component
video terminal.
images of OVD-Video discs are output
from
the COMPONENT VIDEO OUT tenninals.
Analog
Audio
Output
IBosoi
e 2ch
(Oownmixl
+
5.1
ch:
When
connecting to 2ch
AUDIO
OUT
or
5.1ch AUDIO
When
connected with
AUDIO
OUT
terminals, you can set OUT.
(q
37)
the unit to output the
best
possible sound for your speakers.
e7.1ch:
When
connecting to 7.1ch
AUDIO
OUT.
(q
37)
*
I
~
RQT9378
To Next Page
Loading...
