34
34
34
34
36
TV
screen
and
video
Page
------_._---,-.------------
_
..
_._._----_._--_.
__
._----_.
__
._----_._~--~~---------._--------------,-.-.+._--_.,
I
The
images
from
this
unit
eMake
sure that the television
is
connected to either the VIDEO
OUT
terminal,
11
I
do
not
appear
on
the
COMPONENT
VIDEO
OUT
terminals
or
HDMI AV
OUT
terminal on this unit.
I
television.
eMake
sure that the television's input setting (e.g.,
VIDEO
1) is correct.
l
eAn
incorrect resolution is selected
in
"Component Video Resolution", when the
Picture
is
distorted.
television
is
connected to
COMPONENT
VIDEO
OUT
terminals. While stopped,
press and hold
[.]
and
[~]
(PLAY) on the main unit at the same time for
more
!
Jittering
occurs.
than 5 seconds to cancel this setting. Set the item again.
t
elf
"24p
Output"
is
set
to
"On"
when
the
unit
is
connected
to
a
TV
through
any
terminal other
I
i
than
HDMI,
images
may
not
display
properly.
In
this
case,
set
"24p
Output"
to
"Off'.
eWhen
"24p Output" is set to "On", HOMI authentication takes place where 24p
I images switch to other images, and a black screen is displayed.
eWhen
"24p Output" is set to "On", jittering
may
occur while playing DVD-Video
other than 24p images. In this case, turn "24p Output" to "Off'.
elm:
Images
may
not be output due to
how
files were created.
-An
incorrect resolution is selected
in
"HDMI Resolution", when the television is
connected to HDMI AV
OUT
terminals. While stopped, press and hold
[.]
and
[~]
(PLAY)
on the main unit at the same time for more than 5 seconds to cancel
this setting. Set the item again.
However,
Dolby Digital
Plus,
Dolby TrueHD,
and
DTS-HD
audio
are
not output
in
bitstream.
To
output
the
bitstream, select "Restore Default
Settings"
to
restore
the
factory presets
and
make
proper settings.
ePicture may not be seen when more than 4 devices are connected with HDMI
cables. Reduce the number
of
connected devices.
The
screen
changes
automatically.
Video
is
not
output.
Video
is
not
output
in
high
definition.
The
4:3
aspect
ratio
picture
expands
left
and
right.
Screen
size
is
wrong.
There
is
a
lot
of
after-image
when
playing
video.
When playing DVD·Video using
progressive output, one part
of
the picture momentarily
appears
to
be doubled up.
Still
pictures
(JPEG)
do
not
play
back
normally.
-When
the
"Screen Saver Function"
in
the
Setup
menu
is
set
to
"On",
the
display
may
return
to
the
screen
saver
mode
automatically if there
is
no
operation
for
10
minutes or
more.
eAn
image is not output from the
COMPONENT
VIDEO
OUT
terminal
or
the
VIDEO
OUT
terminal when the "High Clarity Sound" is enabled. Set the "High
Clarity Sound" in the on-screen menu to
"Off'
to use the
COMPONENT
VIDEO
OUT
terminal or the VIDEO
OUT
terminal.
eHigh definition video cannot be output through the
VIDEO
OUT
terminals.
eConfirm that the "HDMI Video Mode", "HDMI Resolution", and "Component Video
Resolution"
in
the Setup menu are set properly.
-Use
the
television
to
change
the
aspect. Refer
to
your television's operating instructions.
eWhen
using a component video cable, set "Progressive" to "Video". If the situation
is not restored after that, set "TV Aspect" to "4:3 Pan & Scan".
eWhen
using an HDMI cable, change "TV Aspect" type to "16:9".
eTurn "3D NR"
or
"Integrated NR" off if it
is
on.
-
When
you
use
the
HDMI
AV
OUT
terminal
for
video
output,
follow
the
steps
below
for
setting.
1 Connect this unit to the
TV
with any cable except the HDMI cable.
2
When
you connect with the Component Video cable, set "HDMI Video Mode" to
"Off'
and "Component Video Resolution" to "480i"
in
the Setup menu.
eThe
images that were edited on the PC, such as Progressive JPEG, etc.,
may
not
play back.
33
31
34
31,34
34
31
34
38
Sound
No
sound.
eCheck
the connections and the "Digital
Audio
Output" settings. Check the input
11-13,33
Low
volume.
mode
on the amplifier/receiver if you have connected one.
Distorted
sound.
ePress
[AUDIO] to select the audio.
21
Cannot
hear
the
desired
e18080;: When the unit
is
connected to an amplifier/receiver with the
AUDIO
OUT
34,37
audio
type.
terminal, set "Analog Audio Output" and match multi channel speaker settings. If
these are not set properly, the audio is not output correctly.
e]'Q!l9~:
When connected to an amplifier/receiver or
any
other devices using both 34
AUDIO
OUT
terminal and HDMI AV
OUT
terminal, the audio from
AUDIO
OUT
terminal may not be output with the desired audio depending on the specifications
of
the connected devices, etc. Set "HDMI Audio Output" to "Off', when you
output
multi-channel surround sound from
AUDIO
OUT
terminal.
-The
sound effects
(Re-master,
V.
Surround, etc.) will
not
work
when
the
bitstream signal
is
-
output
from
the
HDMI
AV
OUT
terminal or
the
DIGITAL
AUDIO
OUT
terminal.
elm:
Audio
may
not be output depending on
how
files were created.
-
eAudio
may not be heard when more than 4 devices are connected with HDMI
-
cables. Reduce the number
of
connected devices.
eTo output audio from a device connected with an HDMI cable, set "HDMI Audio
34
Output" to "On"
in
the Setup menu.
Cannot
switch
audio.
I
eThere
are discs for which audio cannot be changed because
of
how the disc was
-
created.
-When connecting
an
amplifier/receiver using a coaxial
cable
U'-~~Q.),
optical digital audio
12,13,33
cable
or
an
HDMI
cable,
you
cannot switch
the
audio if "Dolby D/Dolby 0 +/Dolby TrueHD"
or
"DTS/DTS-HD'
is
set
to
"Bitstream".
Set
"Dolby D/Dolby 0 +/Dolby
TrueHD"
or
"DTS/
DTS-HD"
to
"peM"
or
connect using
AUDIO
OUT
terminal.
43
ROT9378
To Next Page
Loading...
