14
RQT6559
Getting started
STEP 5 Selecting TV screen type
Change the settings if you:
≥Connect the unit to a widescreen 16:9 aspect television.
➜Set “TV Aspect” to “16:9”.
≥Connect the unit through the COMPONENT video terminals
(➜page 10) to a television compatible with progressive video sig-
nals (480P).
➜Set “TV Type” to “480P”.
1 Press [SETUP] to show the menus.
2 Press [3, 4] to select “TV Screen”
and press [1].
3 Press [3, 4] to select “TV
Aspect” and press [ENTER].
4 Press [3, 4] to select “16:9” and
press [ENTER].
3 Press [3, 4] to select “TV
Type” and press [ENTER].
4 Press [3, 4] to select “480P” and
press [ENTER].
≥When playing back, select Video in the on-screen menu and set
“Transfer” according to the type of material being played
(➜page 44).
To return to the previous screen
Press [RETURN].
When you are finished
Press [SETUP].
2
≥
3
≥
4
RETURN
1
TAB
SELECT
Antenna System
Auto Channel Setting
Channel Caption
Preset Channel Caption
Manual Channel Caption
VCR Plusi CH Setting
CATV
Channel
SET UP
RETURN
Set Up
Disc
Video
Audio
Display
TV Screen
TAB
SELECT
TV Aspect
4:3 TV Settings for DVD-Video
TV mode(4:3)
4:3
Letterbox
Pan&Scan
SET UP
RETURN
Set Up
Disc
Video
Audio
Display
TV Screen
4:3 TV Settings for DVD-RAM
TV Type
480I
ENTER
Channel
TV Aspect
TV Type
!?
SET UP
Set Up
Disc
Video
Audio
Display
SELECT
ENTER
TV Aspect
RETURN
4:3
16:9
TV Screen
Channel
!?
SET UP
Set Up
Disc
Video
Audio
Display
SELECT
ENTER
TV Type
RETURN
480I
480P
TV Screen
Channel
15
RQT6559
Getting started
STEP 6 Television operation
!?
You can control televisions by entering the remote control code.
1 Refer to the chart below for the code
for your television.
2 Press and hold [Í, POWER TV] and
enter the two-digit code with the
numbered buttons.
≥For example: 01, press [0] ➜ [1].
≥Test by turning on the television and changing channels.
Repeat the procedure until you find the code that allows
correct operation.
[Note]
≥If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote
control is not compatible with your television.
≥This remote control works with most recently manufactured televi-
sions, but may not be able to control older models.
∫ Operation
Point the remote control at the television.
DVD/TV
DVD
VCR Plus+ TV/VIDEO
REC MODE
REC
CH
VOLUME
TV
TV
DVD
123
789
0
100
4
5
6
SLOW/SEARCH
SKIP
DIRECT NAVIGATOR
TOP
MENU
MENU
RETURN
FUNCTIONS
PROG/CHECK
DISPLAY
TIME SLIP
ADD/DLT
ENTER
PLAY LIST
CANCEL
POWER
ÍÍ
2
TV/VIDEO
W, X, CH
DVD, TV
r, s, VOLUME
2
Code No. Manufacturer
01 Panasonic/National QUASAR
02 Panasonic/National QUASAR
03 MAGNAVOX SYLVANIA PHILIPS (RC-5)
04 ZENITH
05 THOMSON RCA GE
06 SHARP
07 SHARP
08 SONY
09 TOSHIBA
10 SANYO FISHER
11 JVC
12 HITACHI
13 MITSUBISHI
14 SAMSUNG
15 GOLDSTAR/LG
16 GOLDSTAR/LG
17 GOLDSTAR/LG
18 SAMSUNG
19 SAMSUNG
Operation Button
On and off [Í, POWER TV]
Video input mode [TV/VIDEO]
Channels
(Switch [DVD, TV] to “TV”.)
[W, X, CH]
or
Numbered buttons
Example:
Channel “5”: [0] ➜ [5]
Volume [r, s, VOLUME]
To Next Page
Loading...
