Panasonic KX-TGP500 User Manual (English)

Other manuals for Panasonic KX-TGP500

User Guide67 pages

Administrator's Guide284 pages

Admin Guide6 pages

Quick User Guide22 pages

Get To Know Guide2 pages

Set Up And Usage Instructions12 pages

Quick Reference Guide2 pages

Configuration Guide12 pages

Quick Start Guide30 pages

Quick Guide32 pages

Questions and Answers:

E
edward06Sep 7, 2025
What to do if I cannot register a handset to the base unit of my Panasonic Cordless Telephone?
- M
  Mary ParkSep 8, 2025
  If you cannot register a handset to the base unit of your Panasonic Cordless Telephone, it might be because the maximum number of handsets (6) is already registered. Cancel unused handset registrations from the base unit. Also, make sure you are entering the correct PIN. If you forget your PIN, contact your phone system dealer. Ensure that the handset and base unit are away from other electrical appliances.
T
Tracy McdowellAug 25, 2025
Why does my Panasonic Telephone handset beep and/or flash?
- M
  Melissa JonesAug 25, 2025
  If your Panasonic Telephone handset beeps and/or flashes, it means the battery charge is low. You should fully charge the batteries.
P
pearsonelizabethAug 25, 2025
What to do if my Panasonic KX-TGP500 is not ringing?
- C
  Cindy MitchellAug 26, 2025
  If your Panasonic Telephone handset is not ringing, the ringer volume may be turned off. Adjust the ringer volume. Call forward, Do not disturb, or Block anonymous calls may have been programmed by your administrator.
C
Caitlin MckinneySep 8, 2025
What to do if my Panasonic Cordless Telephone rings while programming?
- B
  Brian SmithSep 8, 2025
  If your Panasonic Cordless Telephone starts ringing while you are programming it, a call is being received. Answer the call and try programming again after hanging up.
S
shane75Sep 12, 2025
Why is the STATUS indicator on my Panasonic Telephone lit in amber even when the Ethernet cable is connected?
- D
  Dylan TerrellSep 12, 2025
  If the STATUS indicator lights in amber although the Ethernet cable is connected properly, the base unit’s IP address may conflict with the IP addresses of other devices on your local network. Check the base unit’s static IP address.
J
Julie BrownSep 3, 2025
What to do if I fully charged the batteries, but my Panasonic Telephone still flashes or displays 0?
- S
  Sean WrightSep 3, 2025
  If you have fully charged the batteries, but your Panasonic Telephone still flashes or displays 0, clean the charge contacts and charge again. It also may be time to replace the batteries.
K
Kenneth MorganSep 3, 2025
Why I cannot register a handset to the Panasonic KX-TGP500 base unit?
- P
  Paula LeonardSep 3, 2025
  If you cannot register a handset to the base unit, the maximum number of handsets (6) may already be registered. Cancel unused handset registrations from the base unit. You may have entered the wrong PIN. Place the handset and the base unit away from other electrical appliances.
H
harrisonsandraSep 13, 2025
Why can't I program items on my Panasonic KX-TGP500?
- B
  Becky JohnsonSep 13, 2025
  If you cannot program items on your Panasonic Telephone, it may be because programming is not possible while either another handset or the base unit is being used. Try again later. Programming is also not possible while the base unit is downloading data. Wait until the STATUS indicator stops flashing and lights in steady green.
H
Holly GuerreroAug 29, 2025
What to do if my Panasonic Cordless Telephone does not work?
- S
  Sonya HaasAug 29, 2025
  If your Panasonic Cordless Telephone is not working, ensure the batteries are correctly installed and fully charged. Also, check all connections. Try resetting the unit by unplugging the AC adapter, then reconnecting it. If it still fails, the handset may need to be registered to the base unit.
M
meyerstannerAug 29, 2025
Why does my Panasonic Cordless Telephone handset beep and/or flash?
- B
  Brittany LambertAug 30, 2025
  If the handset of your Panasonic Cordless Telephone is beeping and/or flashing, it indicates that the battery charge is low. You should fully charge the batteries.

Panasonic KX-TGP500 Specifications

General

Wireless Technology	DECT
Frequency	1.9 GHz
Base Station Handsets Supported	6
Simultaneous Calls	3
Protocols Supported	SIP
Caller ID	Yes
Call Waiting	Yes
Conference Calling	Yes
Voicemail	Yes
Handset Speakerphone	Yes
Power	AC Adapter
Network	Ethernet
PoE	Yes
Headset Jack	2.5mm
Codecs	G.711, G.729
Display	LCD
Range	Up to 300 meters outdoors, 50 meters indoors