Panasonic LUMIX DMC-G6P - 9.1.3. Disassembly Procedure

47
9.1.3. Disassembly Procedure
No. Item Fig Removal
1 Rear Case Unit (Fig. D1) Memory Card
Battery
2 Screws (A)
2 Screws (B)
2 Screws (C)
2 Screws (D)
(Fig. D2) 2 Locking tabs
Eye Cup Unit
2 Screws (E)
FP9003 (Flex)
FP9009 (Flex)
Rear Case Unit
2 Main P.C.B. (Fig. D3) 1 Screw (F)
3 Screws (G)
FP9001 (Flex)
FP9002 (Flex)
FP9004 (Flex)
FP9006 (Flex)
FP9007 (Flex)
FP9008 (Flex)
FP9010 (Flex)
FP9011 (Flex)
FP9012 (Flex)
1 Locking tab
Main P.C.B.
3 Top Unit,
Flash P.C.B.
(Fig. D4) 1 Screw (H)
2 Screws (I)
Main Heat Sink
2 Screws (J)
(Fig. D5) 3 Locking tabs
3 Locking tabs
Battery Con Cover
(Fig. D6) FP8502 (Flex)
1 Screw (K)
1 Screw (L)
Solder (4 points)
Top Unit
Flash P.C.B.
4 Front Case Unit (Fig. D7) 2 Screws (M)
1 Screw (N)
2 Screws (O)
(Fig. D8) Front Case Unit
Jack Door
5 Mount Box Unit (Fig. D9) 3 Screws (P)
Mount Box Unit
(Fig. D10) (IMPORTANT NOTICE)
6 NFC Antenna Unit (Fig. D11) 2 Hooking parts
1 Convex
1 Screw (Q)
1 Hooking part
Side Frame (R)
NFC Antenna Unit
7 Wi-Fi P.C.B. (Fig. D12) 1 Screw (R)
2 Convexes
Wi-Fi P.C.B.
8 Battery Frame (Fig. D13) 1 Screw (S)
2 Convexes
Wi-Fi Earth Plate
(Fig. D14) 1 Locking tab
3 Convexes
Battery Frame
9 Battery Door Unit (Fig. D15) Battery Door Shaft
Battery Door Spring
Battery Door Unit
10 Battery Lock Knob (Fig. D16) 2 Locking tabs
Condenser Holder
Battery Lock Spring
Battery Lock Knob
11 LVF Unit (Fig. D17) 2 Screws (T)
LVF Unit
12 LVF Module (Fig. D18) 4 Locking tabs
LVF Cover Unit
LVF Module
LVF Heat Radiation Pad
1 Locking tab
LVF Heat Sink
LVF Cover
13 LVF Lens Unit (Fig. D19) 4 Locking tabs
LVF Case Top
1 Screw (U)
LVF Click Plate
1 Screw (V)
LVF Dial
LVF Gear
LVF Guide Shaft
LVF Lens Unit
14 Mic P.C.B. (Fig. D20) FP4201 (Flex)
FP4202 (Flex)
1 Screw (W)
2 Convexes
Mic P.C.B.
15 Ext Mic P.C.B. (Fig. D21) 2 Screws (X)
FP4401 (Flex)
Ext Mic P.C.B.
16 Hot Shoe FPC Unit (Fig. D22) Solder (4 points)
3 Convexes
Hot Shoe FPC Unit
17 Flash Lock Lever (Fig. D23) 1 Convex
Strap Holder (R)
Flash Lock Spring
Flash Lock Lever
18 Hot Shoe Unit,
Mic Unit
(Fig. D24) Shoe Spring
4 Screws (Y)
Hot Shoe Plate
Hot Shoe Unit
(Fig. D25) 2 Locking tabs
Mic Net
Mic Net Tape
Mic Cushion (A)
Mic Cushion (B)
Mic Unit
Mic Cushion (C)
19 Flash Unit (Fig. D26) 2 Screws (Z)
2 Hooking parts
Flash Case Top
Flash Unit
20 Hinge SW FPC Unit (Fig. D27) 2 Screws (a)
2 Screws (b)
Hinge SW FPC Sheet
Hinge Arm Cover
2 Screws (c)
5 Convexes
Hinge Plate
Solder (4 points)
(Fig. D28) 5 Convexes
Hinge SW FPC Unit
No. Item Fig Removal