What to do if my Panasonic NA-128VB6WAE Washer is not draining water?
If your Panasonic Washer isn't draining, first check the drain hose for any obstructions or bends. Then, inspect the pump filter and clean it if necessary. Also, make sure the clothes are spread inside the machine in an orderly and well-balanced manner.
Why is the spinning process delayed in my Panasonic NA-128VB6WAE?
The delay or absence of spinning in your Panasonic Washer might not indicate a failure. The unbalanced load control system is designed to distribute clothes evenly. It will attempt to redistribute the load, and once the clothes are balanced, the spinning process will begin. For future washes, ensure you place clothes into the machine in a well-balanced manner.
Why my Panasonic Washer is not receiving water?
If your Panasonic Washer isn't filling with water, start by checking if the water tap is fully open. Then, inspect the water inlet hose for any kinks or bends that might be obstructing the flow. Also, the water inlet hose or valve inlet filters could be blocked; clean them to ensure proper water flow. Finally, make sure that the door is completely shut until you hear a click.
How to stop my Panasonic Washer from vibrating?
If your Panasonic Washer is vibrating excessively, begin by adjusting the feet to ensure the machine is level. Make sure the transportation screws have been removed. Also, check that you're not overloading the machine and that clothes are distributed evenly inside. Note that a small amount of clothes might not prevent the operation of the machine.
How to remove detergent residues on clothes from Panasonic NA-128VB6WAE?
If you notice detergent residues on clothes after washing in your Panasonic Washer, it could be due to undissolved detergent particles sticking to the fabric as white stains. Calibrate the machine for a “Rinsing” program to add an extra rinse cycle, or remove the stains after drying with a brush.
How to troubleshoot a Panasonic NA-128VB6WAE that does not operate?
If your Panasonic Washer isn't starting, several things could be the cause. First, make sure it's properly plugged into the socket. Next, check the fuse and replace it if it's defective. Ensure you've pressed the start/pause button and that the program knob is set to the desired program, not the '0' (off) position. Also, be sure the door is completely shut until you hear a click. Finally, check if the child lock is active; if so, refer to section 5.3 for instructions on deactivating it.
Why is there excessive foam in the detergent drawer of my Panasonic NA-128VB6WAE Washer?
If you see too much foam in the detergent drawer of your Panasonic Washer, it could be due to using too much detergent or using the wrong type. To stop the foam, press the start/pause button, then dilute one tablespoon of softener in half a liter of water and pour it into the detergent drawer. After 5-10 minutes, press the start/pause button again. In the future, use only detergents produced for full automatic machines and adjust the amount of detergent properly.
Why is the washing result not good in my Panasonic NA-128VB6WAE Washer?
If the washing result with your Panasonic Washer isn't satisfactory, it might be due to overloading the machine. Make sure not to exceed the maximum capacity. Hard water may also be a factor, so adjust the amount of detergent according to the detergent producer's instructions. Finally, ensure the clothes are well-distributed inside the machine.
Why is the washing result bad in my Panasonic NA-128VB6WAE?
If you're getting poor washing results from your Panasonic Washer, the laundry might be too dirty for the program you've selected; try selecting a more suitable program. Also, you might not be using enough detergent, so increase the amount according to the detergent's instructions.
Explains warning indicators, attention symbols, and safety icons used throughout the manual.
Details precautions for electrical connections, preventing shock, and proper wiring.
Covers safe practices for using specified parts, handling rotating components, and repair procedures.
Recommends wearing gloves and appropriate clothing during servicing for protection.
Lists technical details, capacity, dimensions, and performance metrics of the washing machine.
Describes the information found on the appliance's name plate, including model and electrical ratings.
Guides on removing transport screws and adjusting machine feet for stable installation.
Details the necessary electrical supply and plug requirements for the appliance.
Provides instructions for connecting the water inlet and drain hoses correctly.
Illustrates the detergent box assembly, including valves and hoses.
Explains the LCD screen, function buttons, and program selector knob.
Outlines available wash programs, their settings, and power/water consumption.
Describes how to enable and disable the child lock feature on the control panel.
Details the steps to set the program selector and buttons to start the autotest.
Explains the sequence of tests performed during autotest and their expected results.
General| Appliance placement | Freestanding |
|---|---|
| Loading type | Front-load |
| Colour of product | White |
| Built-in display | Yes |
| Door hinge | Left |
| Drum material | Stainless steel |
| Rated capacity | 8 kg |
| Maximum spin speed | 1200 RPM |
| Spin-drying class | B |
| Washing class | A |
| Number of washing programs | 16 |
| Delayed start timer | Yes |
| Delay start (max) | 24 h |
| Energy efficiency class | A+++ |
| Annual water consumption washing | 9900 liters |
| Width | 60 cm |
| Height | 850 mm |
To Next Page