Why is no water going into my Panasonic NA-128VB5?
If no water is going into your Panasonic Washer, the water tap might be turned off, so turn it on. The water-supply hose may be frozen, so thaw the water-supply hose. The water supply may be disrupted, so check the water supply. Also, the water-supply filter may be clogged, so clean the water-supply filter.
What to do if the door doesn't open on my Panasonic NA-128VB5 Washer?
If the door of your Panasonic Washer does not open, the door lock may be activated, so deactivate the door lock. Also, the water temperature or level may be too high, so wait for the water temperature or level to decrease.
Why is the laundry still wet after spinning in my Panasonic NA-128VB5?
If the laundry is still wet in your Panasonic Washer after the spinning finishes, it might be due to an unbalanced load. Try to adjust the laundry load. Also, if the laundry is too light, add one or two bath towels. If the laundry gets tangled up, untangle it.
Why does the spin cycle repeatedly start and stop on my Panasonic Washer?
If the spin cycle repeatedly starts and stops in your Panasonic Washer, intermittent spinning of the tub helps the spin process to operate quietly, so no action needed. The laundry may be too light, so add one or two bath towels.
Why is there so much foam in my Panasonic NA-128VB5 Washer?
If there is a lot of foam in your Panasonic Washer, the amount of foam varies, depending on the temperature, level and softness of the water, so adjust water temperature, level, or softness. Also, you may have used too much detergent, so reduce the amount of detergent used. The type of detergent you are using may cause excess foam, so change to a low-foam detergent.
How to fix buttons that don't work on my Panasonic Washer?
If the buttons on your Panasonic Washer do not work, ensure the washing is not in progress, because the programme, temperature, spin speed, preset time, Extra Rinse, Easy Iron or Speed/Eco function settings cannot be changed while washing is in progress. Also, the child lock may be activated, so deactivate the child lock.
Why is there no foam in my Panasonic NA-128VB5 Washer?
If there is no foam or hardly any foam in your Panasonic Washer, the amount of foam varies, depending on the temperature, level and softness of the water, so adjust water temperature, level, or softness. You may have put powdered detergent directly into the drum; you must put it in the detergent drawer, so use the detergent drawer for powdered detergent. You may not be using enough detergent, so increase the amount of detergent used. You may be using a reduced-foam type of detergent, so use a regular detergent instead. Heavily soiled laundry and larger loads of laundry may reduce the amount of foam, so wash smaller or less-soiled loads.
Why does fabric softener overflow in my Panasonic NA-128VB5 Washer?
If fabric softener overflows in your Panasonic Washer, the softener may have exceeded the MAX level for the detergent drawer, so ensure softener is below the MAX level. You may have spilt the liquid by closing the detergent drawer too strongly, so close the detergent drawer gently.
Why does rinsing begin before the spin process finishes in my Panasonic NA-128VB5 Washer?
If rinsing begins before the spin process finishes in your Panasonic Washer, after washing, excess foam may remain, so the water is drained out and refilled to wash it away. Wait for the rinsing process to complete.
Why do foam and water remain in the door seal of my Panasonic NA-128VB5 Washer?
Although some foam and water might remain in the door or door seal of your Panasonic Washer depending upon the state of the laundry and the amount of detergent used, the performance of the rinse cycle is unaffected, so no action needed.
Safety guidelines for operating the appliance, especially concerning children.
Procedure for initial checks before operating the appliance for the first time.
Instructions for the initial operation of the appliance to rinse out residue.
Details on the detergents and additives for the detergent compartment.
Explanation of the control panel buttons and the programme selection dial.
Description of the various indicators and information shown on the appliance's display.
Step-by-step guide on how to set up a washing cycle.
Instructions on how to fold and place blankets and bedspreads in the drum.
Guide on how to clean the drain filter monthly to ensure proper drainage.
Procedure for removing transport anchor bolts before appliance operation.
A list of checks to perform after installing the appliance to ensure proper function.
General| Power consumption (off) | 0.5 W |
|---|---|
| Water consumption per cycle | - L |
| Energy consumption washing per cycle | 0.77 kWh |
| Annual water consumption washing | 9900 L |
| Annual energy consumption washing | 194 kWh |
| Door color | Black |
| Door hinge | Left |
| Drum volume | 55 L |
| Control type | Rotary, Touch |
| Display type | LCD |
| Loading type | Front-load |
| Product color | White |
| Built-in display | Yes |
| Door opening angle | 140 ° |
| Appliance placement | Freestanding |
| Drum capacity | 8 kg |
| Cycle time (max) | 175 min |
| Delay start (max) | 24 h |
| Residual moisture | 53 % |
| Spin-drying class | B |
| Maximum spin speed | 1200 RPM |
| Minimum spin speed | 400 RPM |
| Noise level (spin) | 74 dB |
| Noise level (wash) | 58 dB |
| Number of washing programs | 15 |
Weight and Dimensions| Depth | 557 mm |
|---|---|
| Width | 597 mm |
| Height | 845 mm |
| Weight | 77000 g |
To Next Page