Panasonic NV-DS28A - Using a Card

»-
MARCH* FADE
STILL BUC
NOW WR I
T I NQ
CARD
Mode
Using
a Card
A
Card
can
be used
to
record
still
pictures.
inserting
a Card
Before
inserting
a
Card,
be sure
to turn off
the
Movie
Camera.
1
Slide
the
[OPEN]
Lever
and
open the
Card
Compartment.
2
Hold the
Card
with
its notch
O
facing
left
and
insert
it
in the
Card
Compartment.
3
Push
the
part
©
and close
the
Card
Compartment
securely.
[ACCESS]
Lamp
While
the
Movie
Camera
is making
an
access
to the
Card
(reading,
recording,
playback,
erasing,
moving
of
images),
the
[ACCESS]
Lamp lights
up.
•While
the
[ACCESS]
Lamp
0
is on,
never
attempt
to open
the
Card
Compartment,
to pull
out
the Card,
to turn
off
the
Movie
Camera,
or
to
switch
the
[TAPE/CARD]
Selector.
Such
actions
will
damage
the
Card,
cause
loss of
recorded
data
and cause
the
Movie
Camera
to
malfunction.
Recording
on
a
Card
Still
pictures
can
be recorded
on a Card
from
the
Movie
Camera
lens
as weil
as from
scenes
that
have
already
been
recorded
on a
cassette.
Card
Photoshot
Recording
from
the
Movie
Camera
Lens
(CAMERA
Mode)
1
Slide the
[TAPE/CARD]
Selector
towards
[CARD].
2
Press
the
[PHOTO
SHOT]
Button.
•
If nothing
is
recorded
for
approximately
6 minutes,
the
Movie
Camera
is
turned
off
automatically.
•
When
the [TAPE/CARD]
Selector is
set to
[CARD],
you cannot
record
to the
Tape.
Recording
from
a Cassette
(VCR
Mode)
1
Slide
the
[TAPE/CARD]
Selector
towards
[CARD].
2
Start
playback
and
set the
Movie
Camera
to Still
Playback
Mode
at
the
scene
you
wish
to
record,
and
press
the
[PHOTO
SHOT]
Button.
Selecting
the
quality
of
Card
Photoshot
images
1
Set
[CAMERA
FUNCTIONS]
or [VCR
FUNCTIONS]
»
[CARD
SETUP]
»
[PICTURE
QUALITY]
» a
desired
image
quality.
Maximum
number
of Images
recordable
on
a Card
(8MB)
(FINE]
(high
image
quality):
approximately
45 pictures
[NORMAL}
(Normal):
approximately
95
pictures
[ECONOMY]
(tow image
quality):
approximately
190
pictures
Automatically
Copying
Still
Pictures
That
Have
Already
Been
Recorded
on
a Tape
The images
with
the
Photo Index
signals
are
automatically
recorded
to the
Card.
1
Set the
Movie
Camera
to Still
Playback
Mode
at the
scene
immediately
before
you want
to
start moving
images.
2
Set
[VCR
FUNCTIONS]
»
[PLAYBACK
FUNCTIONS]
»
[RECORD
TO CARD]
»
[YES].
•
Search
starts
from the
current
Tape
position,
and images
with
Photo
Index
signals are recorded
onto
the Card
sequentially.
•
During copying,
the Indication
Q
appears.
To Stop
Automatic
Recording
Press
the
[]
Button.
•For
other notes
concerning
this item,
see page 42.