Panasonic Omnivision PV-2601 - Timer Recording Using vor Buttons Cuts a

Cancel a Timer Recording:
Recording is in progress
1
2
Push the POWER button to release
the VCR from timer mode.
Push the STOP button within 10
seconds of pushing the POWER
button to cancel the recording.
The TIMER indicator goes out in the
Multi Function display.
Replace Program Contents:
Recording is not in progress
1 Push the PROG
button to display al!
currently set
programs.
Rotate and push the
Wheel to select and
enter the desired
timer recording.
(See page 16.)
Rotate and push the
Wheel to select and
enter replacement
information.
P DT STRAT STOP CH SPD
1 --
2 “0: OOP 12: “OOP 125 SLP
3 10 8:00P 9:00P 10 SP
4 SU 9:00P10:00P L SLP
SELECT 1-8:ROTATE WHEEL
¡PUSH PROG KEY
START STOP CH
£7
8 oh) 10:00? 12:00P 125
BY ROTATING WHEEL
SH CLEAR : PUSH WHEELS
TO END PUSH PROG K
Push the PROG button to exit this mode
and return to the normal TV screen.
Review or Clear Program Contents:
Recording is not in progress
Push the PROG
button to display all
currently set
programs.
Rotate the Wheel to
select the desired
program number.
Push the CLEAR
button to clear the
program.
P DT STAAT STOP CH SPD
4 SU 9:00P10:00P 1 SLP
SELECT 1-8:ROTATE WHEEL
NTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
ENO :PUSH PROG KEY
P DT STRAT STOP CH SPD
2 a 10: DOOR 12: 00P 125 SLP
3 10 8:00P 9:00P
4 $U 9:00P10:00P ste
SELECT +-B:ROTATE WHEEL
ENTER = :PUSH WHEEL
END :PUSH PROG KEY
Push the PROG button to exit this mode
and return to the normal TV screen.
- @eeeee
COCO SOSEE HOSES HEHEHE HHHOHEHHEHEESEEEEEOHEREEHHEHEHETETERLEECEHAEHELASETAHLELESEESEAHEHAEAEOHES
.
Timer
Recording
J
Using
VCR
Buttons
A
timer
recording
can
be
set
up
using
the
buttons
on
the
VCR.
If
necessary,
the
clock
can
also
be
set.
FF REC/TIME
POWER Multi
Function
Display
WSELECTA SET PROGRAM
. Hold down
REC/TIME.
= BY SELECT a/¥ KEY
ds E
Push FF to
enter the
program mode.
* If the clock is not set, pushing these | /I\___________ DST:ON
buttons will display the SET CLOCK
screen. In this case, proceed with steps {BY SELECT 4/w KEY
2 and 3 to set the clock and then steps |NEXT, PUSH SET KEY OR
2-6 to set a timer recording. TO ENO PUSH FAQG SEY
+ Once the VCR is in the Program mode, the PLAY, REC, FF,
and REW buttons on the VCR operate only as specified above.
(2) Push REW or PLAY to
@ a
O) make your selection.
(for down)
S e
* Push SET (FF) repeatedly to move to a
particular jtem for setting or correction.
| (for up)
Push FF to set
and move on to
the next item.
Items to be Set:
* recording DATE
* START time
* STOP time
* CH(annel), or LINE
* SPEED (SP, LP, SLP)
When the program is completed...
(4) i Push REC/TIME
and ©
and FF to display
(at the same time)
program contents.
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
(5) © Push REC/TIME and
FF to exit this mode.
(at the same time)
Push POWER off
c to set the timer
Ss I “
— Diba! —-
- | ‘S
Multi Function Display
« itis not possible to clear a timer program using the VCR buttons.
Piease use the Remote Control.
* When recording programs via a cable box, make sure the cable
box is left on and tuned to the desired channel.
S
O
bom 4
O
ð
=
e
Y
3
O
©