Panasonic Omnivision PV-M1346

Cancel a Timer Recording:
Recording is in progress
Hold down the STOP button for a few
seconds to cancel the Timer Recording.
• Any future daily or weekly recordings will be
performed as programmed.
Replace Program Contents:
Recording is not in progress
P OT STRAT STOP CH SPO
I Push the PROG ж А ЫДБ
button
to
display
EME
all currently
4 SU 9:00p 10:00) L SLP
SELECT 1-8:ROTATE WHEEL
set programs. ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END :PUSH PROG KEY
2 Rotate and push
the Wheel to
select and enter
the desired timer
recording.
(See page 16.)
QAJE], START STOP CH
5 i 10:00P 12:00P 125
BY ROTATING WHEEL
TO END | PUSH PROG KEY
3 Rotate and push the Wheel to select
and enter replacement information.
4 Push the PROG button to exit this
mode and return to the normal TV
screen.
Review or Clear Program Contents:
Recording is not in progress
I Push the PROG
button to display
all currently set
programs.
Р OT STRAT STOP CH SPD
4 SU 3:00p10:90p Е SLP
SELECT 1-8: aida: WHEEL
: H
2 Rotate the Wheel
Н
ве
the
P
DT
STRAT
STOP
CH
SPD
g----:--
--:.-
esired
program
2 8
10:00p12:00p
125
SLP
number.
eee
to
азр
4 SU 9:00р10:00р L SLP
SELECT 1-8:ROTATE WHEEL
3 Push the CLEAR ENTER ;PUSH WHEEL
button to clear the END :PUSH PROG KEY
program.
4 Push the PROG button to exit this
mode and return to the normal TV
screen.
€ 990606€0900€0900600€00000090090900009€€060906008006€00909000€9$0900000900000900000909000002000800009009000000800090090000000000000990009€09280800€090
limer Recording
Using Unit Buttons
A timer recording can be set up using the buttons on the
Combination VCR. If necessary, the clock can also be set.
REW PLAY ЕЕ REC/TIME
Gel > 1 20)
EA
WSELECTA SET PROGRAM
Hold down
REC/TIME.
START STOP
Do
A p
Push FF to
E2;
enter the
SELECT STAAT DATE
BY SELECT a/¥ KEY
NEXT, PUSH SET KEY OR
TO END PUSH PROG KEY
program mode.
* If the clock is not set, pushing
these buttons will display the SET
CLOCK screen. in this case, set
the clock according to the OSD's
instructions and then set a timer
recording.
• Once the Combination VCR is in the Program mode, the
PLAY, REC, FF, and REW buttons on the Combination
VCR operate only as specified above.
Push REW or PLAY to
make your selection.
MANUAL SET
PUSH SELECT a/¥
SELECT :
SET : PUSH SET KEY
END : PUSH PROG KEY
D сете» c
= down)
(for up)
3) - PushFFtoset Items to be Set:
ED, and move on tọ -recording DATE
the next item. * START time
e STOP time
* CH(annel), or LINE
• SPEED (SP, LP, SLP)
. > Push SET (FF) repeatedly to move to a
particular item for setting or correction.
When the program is completed...
(A . Push REC/TIME
NT) (с) ана Бу and FF їо display
program contents.
_ {at ће same time)
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
(5) | Push REC/TIME and
© ana ©
FF to exit this mode.
(at the same time)
*
It
is
not
possible
to
clear
a
timer
program
using
the
Combination
VCR
buttons.
Please
use
the
Remote
Control.
S
О
=|
Ф
>
c
O
©
5
O
о