To Next PageTo Next PageHow to control Panasonic PT-RS11K Projector with Art-Net?
If you cannot control the projector with Art-Net, verify that the connections between the twisted-pair-cable transmitter and an external device, and between the twisted-pair-cable transmitter and the projector are correctly done. Ensure that [Art-Net SETUP] is set to other than [OFF]. Also, confirm that [NET], [SUB NET], [UNIVERSE], and [START ADDRESS] are set correctly.
How to fix Panasonic PT-RS11K lens shift that cannot be adjusted?
If the lens shift on your Panasonic Projector cannot be adjusted, perform [LENS CALIBRATION]. Also, verify that the Fixed-focus Lens (Model No.: ET?D75LE50) is not attached.
Why is Panasonic PT-RS11K Projector 3D eyewear not functioning?
If your 3D eyewear isn't functioning with the Panasonic Projector, first check if the battery is dead. If you have rechargeable eyewear, charge the battery; if it's a battery type, replace the battery. Also, ensure that the [3D SETTINGS] are correct.
Why is Panasonic PT-RS11K 3D function not working?
If the 3D function on your Panasonic Projector isn't working, check that the [3D INPUT FORMAT] setting in [3D SETTINGS] is correct. Also, check the 3D eyewear settings and ensure that the input signal is supported by the projector.
Why is DIGITAL LINK input image not displayed on Panasonic PT-RS11K?
If the DIGITAL LINK input image is not displayed on your Panasonic Projector: * Ensure the connections between the twisted-pair-cable transmitter and the projector or an external device are correctly done. * Verify that [DIGITAL LINK MODE] is set to [AUTO] or [DIGITAL LINK], and not [ETHERNET]. * Confirm that the input signal is compatible with a twisted-pair-cable transmitter.
Why Panasonic Projector power does not turn on?
If your Panasonic Projector isn't powering on, verify that the power plug is securely inserted into the outlet and that the switch is set to . Also, check if the wall outlet is supplying electricity and if the circuit breakers have tripped. Finally, check whether the light source indicators / or the temperature indicator are lighting or blinking.
Why image from computer does not appear on Panasonic PT-RS11K Projector?
If you're not getting an image from a computer on your Panasonic Projector: * Check if the cable is too long. For D-Sub cables, it should be 10 m (32'10") or shorter. * Verify the external video output on the laptop is set correctly. (The external output settings may be switched by pressing the “Fn” + “F3” or “Fn” + “F10” simultaneously. Since the method varies depending on the computer type, refer to the user manual provided with your computer.)
What to do if Panasonic Projector image does not display correctly?
If the image on your Panasonic Projector is not displaying correctly: * Ensure the SYSTEM SELECTOR is set correctly. * Verify the RGB1 INPUT SETTING is properly configured. * Check the video tape or other image sources for issues. * Confirm that the input signal is compatible with the projector.
Why video from HDMI device does not appear on Panasonic PT-RS11K Projector?
If video from an HDMI compatible device doesn't appear or appears jumbled on your Panasonic Projector: * Check that the HDMI cable is securely connected. * Try turning the power of both the projector and the external device off and on again. * Ensure that the input signal is compatible with the projector.
Why does Panasonic PT-RS11K remote control not respond?
If the remote control is not responding with your Panasonic Projector, consider the following: * Check if the batteries are depleted and replace them if necessary. * Ensure the batteries are inserted with the correct polarity. * Make sure there are no obstructions between the remote and the projector's signal receiver. * Verify the remote is within its effective operating range. * Check if other light sources, like fluorescent lights, are affecting the projection. * Confirm that the REMOTE CONTROL setting in CONTROL DEVICE SETUP is not set to DISABLE. * Check if the terminal is used for contact control. * Verify the ID number setting operation is correct.
General| Contrast Ratio | 20, 000:1 |
|---|---|
| Light Source | Laser |
| Light Source Life | 20, 000 hours |
| Resolution | 1920 x 1200 (WUXGA) |
| Input Terminals | HDMI, DVI-D |
