Panasonic PT-RZ770

Chapter 3 Basic Operations — Switching on/off the projector
58 - ENGLISH
Initial setting (operation setting)
Set the items regarding the operating method depending on the duration of use and the usage of the projector.
After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP]
menu. If you change the settings while using the projector, the duration until the luminance of light source
decreases by half may shorten or the luminance may decrease.
This initial setting (operation setting) is prepared to complete the settings at once during the installation when
the operation of the projector is predetermined. When the [PROJECTOR SETUP] menu → [INITIALIZE] →
[ALL USER DATA] is executed, do not change the setting in the initial setting (operation setting), but press the
<ENTER> button and proceed to next initial setting (installation setting). Request to the person responsible for this
projector (such as a person in charge of equipment or operation) when it is necessary to change the setting.
2/7
100.0%
100.0%
INITIAL SETTING
SET
CHANGEMENU SELECT
OPERATING MODE
CONSTANT MODE
NORMAL
OFF
LINK
GROUP A
ENTER
CALIBRATION TIME
OFF
CALIBRATION MESSAGE
ON
BRIGHTNESS CONTROL SETUP
LIGHT OUTPUT
MAX LIGHT OUTPUT LEVEL
Set the way to use the projector. For details, please
refer to the operating instructions "When the initial
setting screen is displayed".
Note
f The preceding initial setting screen is displayed when the projector is switched on for the rst time after purchase. If the [PROJECTOR
SETUP] menu → [INITIALIZE] → [ALL USER DATA] is executed, the settings before execution are displayed in [OPERATING MODE] and
[MAX LIGHT OUTPUT LEVEL].
f For the relationship between the luminance and the runtime, refer to “Interrelation of luminance and runtime” (x page 60).
f For details on each setting item, refer to the [PROJECTOR SETUP] menu → [OPERATION SETTING].
1) Press as to select [OPERATING MODE].
2) Press qw to switch the item.
f The items will switch each time you press the button.
f Set [OPERATING MODE] to anything other than [ECO], [LONG LIFE1], [LONG LIFE2], and [LONG LIFE3]
when using the projector at an altitude of 2 700 m (8 858') or higher above sea level.
[NORMAL]
*1
Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours.
[ECO]
*1
The luminance will decrease compared to [NORMAL], but set this item to increase the expected life of
the light source. The estimated runtime is approximately 24 000 hours.
[LONG LIFE1]
*1
The luminance will decrease compared to [ECO], but set this item to increase the expected life of the
light source. The estimated runtime is approximately 43 000 hours.
[LONG LIFE2]
*1
The luminance will decrease compared to [LONG LIFE1], but set this item to increase the expected
life of the light source. The estimated runtime is approximately 61 000 hours.
[LONG LIFE3]
*1
The luminance will decrease compared to [LONG LIFE2], but set this item to increase the expected
life of the light source. The estimated runtime is approximately 87 000 hours.
[USER1]
[MAX LIGHT OUTPUT LEVEL] and [LIGHT OUTPUT] can be set individually.[USER2]
[USER3]
*1 The runtime is an estimation when the [PICTURE] menu → [DYNAMIC CONTRAST] is set to [3].
f Proceed to 5) when [NORMAL], [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3] is selected.
3) Press as to select [MAX LIGHT OUTPUT LEVEL].
4) Press qw to adjust.
Operation Adjustment Range of adjustment
Press w.
Increases the maximum level of brightness correction.
8.0 % - 100.0 %
Press q.
Decreases the maximum level of brightness correction.
5) Press as to select [LIGHT OUTPUT].